写完固件，无法登录，卡死。
HELLO! BOOT0 is starting![ 0.35]HELLO! BOOT0 is starting!
[ 0.39]boot0 commit : b58d49ff80aa5ff8865ab68aa2463d4ee0fe1e7d
[ 0.46]boot0 version : 4.0
[ 0.50]set pll start
[ 0.54]set pll end
[ 0.89]rtc value = 0x00000000
[ 0.92]rtc value = 0x00000000
[ 0.95]rtc value = 0x00000000
[ 0.98]rtc value = 0x00000000
[ 0.102]rtc value = 0x00000000
[ 0.105]rtc value = 0x00000000
[ 0.108]DRAMC IS FOUR
[ 0.111]DRAM BOOT DRIVE INFO: V1.1
[ 0.114]Found A40
[ 0.116]Found A40
[ 0.118]Found A40
[ 0.120]Found A40
[ 0.122]Found A40
[ 0.128]PMU: [ 0.129]AXP221
[ 0.131]ddr voltage = 1500 mv
[ 0.134]DRAM CLK =576 MHZ
[ 0.137]DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
[ 0.142]DRAM zq value: 0x003b3bfb
[ 0.147]DRAM SIZE =2048 M
[ 0.150]DRAM ** test OK.
[ 0.153]dram size =2048
[ 0.156]rtc standby flag is 0x00000000, super standby flag is 0x00000000
[ 0.163]card no is 2
[ 0.166]sdcard 2 line count 8
[ 0.169]: mmc driver ver 2016-07-01 15:30
[ 0.173]: wrong freq 2 at spd md 2
[ 0.186]: ***Try MMC card 2***
[ 0.203]: MMC 5.1
[ 0.205]: HSSDR52/SDR25 8 bit
[ 0.209]: 50000000 Hz
[ 0.211]: 7456 MB
[ 0.214]: ***SD/MMC 2 init OK!!!***
[ 0.287]Succeed in loading uboot from sdmmc flash.
[ 0.292]Entry_name = u-boot
[ 0.307]Ready to disable icache.
[ 0.311]0xffffffff 0xffffffff
[ 0.313]0xffffffff 0xffffffff
[ 0.317]0xffffffff 0xffffffff
[ 0.320]0xffffffff 0xffffffff
[ 0.323]0xffffffff 0xffffffff
[ 0.326]0xffffffff 0xffffffff
[ 0.329]Jump to secend Boot.
U-Boot 2014.07 (Jul 25 2019 - 05:35:06) Allwinner Technology
uboot commit : 65b7504a61af7d8b06d7afd9b75cb593144fdcc8
i2c_init: by cpux
i2c_init ok
[ 0.344]pmbus: ready
[ 0.358]PMU: AXP221
[ 0.358]PMU: AXP22x found
[ 0.359]PMU: dcdc2 1160
[ 0.360]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100MhzMBus=400Mhz
set power on vol to default
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1160, onoff=1
dcdc3_vol = 1200, onoff=1
dcdc4_vol = 1100, onoff=0
aldo1_vol = 3300, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dc1sw_vol = 3000, onoff=0
dc5ldo_vol = 1100, onoff=0
dldo1_vol = 3300, onoff=1
dldo2_vol = 3300, onoff=0
dldo3_vol = 3300, onoff=0
dldo4_vol = 2500, onoff=1
eldo1_vol = 2800, onoff=0
eldo2_vol = 1200, onoff=1
eldo3_vol = 2800, onoff=1
gpio0_vol = 3300, onoff=1
gpio1_vol = 3300, onoff=1
find power_sply to end
vbus exist
run key detect
no key found
no uart input
DRAM:2 GiB
fdt addr: 0xb6e8fcd8
Relocation Offset is: 75ee6000
axp: get node error
In: serial
Out: serial
Err: serial
gic: normal mode
[ 0.514]start
drv_disp_init
init_clocks: finish init_clocks.
pwm_request: reg = 0x1c23400. pwm = 0.
request pwm success, pwm = 0.
tv_init:
tv_probe:000
tv0 have no type1
tv0 have no type2
tv0 have no type3
no report hpd work,you need support the switch class!
screen 0 don't support TV!
screen 1 don't support TV!
screen 0 do not support VGA TYPE!
screen 1 do not support VGA TYPE!
tv_init:
drv_disp_init finish
fetch script data boot_disp.output_disp fail
fetch script data boot_disp.output_type fail
fetch script data boot_disp.output_mode fail
fetch script data boot_disp.auto_hpd fail
disp0 device type(1) enable
disp 0, clk: pll(306000000),clk(306000000),dclk(51000000) dsi_rate(306000000)
clk real:pll(308571428),clk(308571428),dclk(51428571) dsi_rate(0)
enable power vcc-lcd, ret=0
[ 1.277]end
workmode = 0,storage type = 2
[ 1.277]MMC: 2
: mmc driver ver 2016-07-01 15:50:00
: mmc_update_timing_para: error sdc_no 2
SUNXI SD/MMC: 2
: 50 MHz...
: sample: 63 - 158(ps)
: ds: 63 - 158(ps)
: 100 MHz...
: sample: 32 - 156(ps)
: ds: 32 - 156(ps)
: 200 MHz...
: sample: 16 - 156(ps)
: ds: 16 - 156(ps)
: media type 0x8000000
: ************Try MMC card 2************
: host caps: 0x6f
: MID 0000d6 PSN 8260d1a0
: PNM 88A398 -- 0x38-38-41-33-39
: PRV 1.1
: MDT m-11 y-2021
: MMC v5.1
: speed mode : HSSDR52/SDR25
: clock : 50000000 Hz
: bus_width : 8 bit
: user capacity: 7456 MB
: boot capacity: 4096 KB
: rpmb capacity: 4096 KB
: ************SD/MMC 2 init OK!!!************
: use default speed mode: 1-HSSDR52/SDR25, ifreq: 2
: ========best spd md: 1-HSSDR52/SDR25, freq: 2-50000000
: already at HSSDR52_SDR25 mode
: erase_grp_size : 0x400WrBlk*0x200=0x80000 Byte
: secure_feature : 0x55
: secure_removal_type : 0x9
: EOL Info(Rev blks): Normal
: Wear out(type A): 0%-10% life time used
: Wear out(type B): Not defined
[ 1.513]sunxi flash init ok
--------fastboot partitions--------
-total partitions:6-
-name- -start- -size-
boot-resource: 1000000 700000
env : 1700000 400000
boot : 1b00000 1000000
rootfs : 2b00000 40000000
usr : 42b00000 9fb00000
UDISK : e2600000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_mmc boot_normal
update dtb dram start
update dtb dramend
PowerBus = 2( 2:vBus 3:acBus other: not exist)
no battery, limit to dc
no battery exist
EnterNormalBootMode sunxi_bmp_display--
reading bootlogo.bmp
1152054 bytes read in 27 ms (40.7 MiB/s)
bmp file buffer: 0x40000000, bmp_info.buffer: 46400000
fetch script data boot_disp.output_full fail
screen_id =0, screen_width =1024, screen_height =600
frame buffer address 46400036
[ 1.772]inter uboot shell
Read addr=40 eeprom addrlen=1 ok!!
The test ok!
secret ok
Hit any key to stop autoboot:0
read partition: boot or recovery
[ 3.102]sunxi flash read :offset 1b00000, 14324561 bytes OK
Android's image name: sun8i_arm
Kernel load addr 0x40008000 size 11613 KiB
RAM disk load addr 0x41000000 size 1353 KiB
[ 3.168]ready to boot
prepare for kernel
: mmc exit start
: 50 MHz...
: sample: 62 - 161(ps)
: ds: 62 - 161(ps)
: 100 MHz...
: sample: 31 - 161(ps)
: ds: 31 - 161(ps)
: 200 MHz...
: sample: 15 - 166(ps)
: ds: 16 - 156(ps)
: mmc 2 exit ok
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.65 (bluesky@a97aa656d1ab) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #39 SMP PREEMPT Mon Jul 29 03:45:11 UTC 2019
[ 0.000000] CPU: ARMv7 Processor revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun8iw11p1, model: sun8iw11p1
[ 0.000000] bootconsole enabled
: RootDevice is "/dev/mmcblk0p7"
: Try to load EMMC ...
e2fsck 1.41.14 (22-Dec-2010)
/dev/mmcblk0p7: recovering journal
/dev/mmcblk0p7: clean, 8436/9648 files, 484381/546296 blocks
mount: proc is already mounted or /proc busy
proc is already mounted on /proc
mount: devtmpfs is already mounted or /dev busy
init asteroidenv##
init qt env########################
Starting sshd: OK
Starting telnetd: OK
Starting vsftpd: OK
================Usrage================
/fbinit means:clean /dev/fb0
/fbinit 0 means:clean /dev/fb0
/fbinit 1 means:clean /dev/fb1
/fbinit 2 means:clean /dev/fb2
================usrage================
cleanning /dev/fb0 ...
clean /dev/fb0 finish
find qt5 installed
D-Bus per-session daemon address is: unix:abstract=/tmp/dbus-JGVHYqurvE,guid=79a711694ed727684d2ceed45e1fda78
Unknown username "pulse" in message bus configuration file
xres = 1024, yres = 600
▒[ 0.0]set pll start
[ 0.3]set pll end
[ 0.5]beign to init dram
[ 0.7]DRAMC IS FOUR
[ 0.10]DRAM BOOT DRIVE INFO: V1.1
[ 0.13]Found A40
[ 0.15]Found A40
[ 0.17]Found A40
[ 0.19]Found A40
[ 0.21]Found A40
[ 0.27]PMU: [ 0.28]AXP221
[ 0.30]ddr voltage = 1250 mv
[ 0.37]PMU: [ 0.38]AXP221
[ 0.40]ddr voltage = 1250 mv
[ 0.51]PMU: [ 0.52]AXP221
[ 0.54]ddr voltage = 1500 mv
[ 0.64]DRAM CLK =576 MHZ
[ 0.67]DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
[ 0.72]DRAM zq value: 0x003b3bfb
[ 0.78]DRAM SIZE =2048 M
[ 0.81]DRAM ** test OK.
[ 0.84]init dram ok
U-Boot 2014.07 (Jul 25 2019 - 05:35:06) Allwinner Technology
uboot commit : 65b7504a61af7d8b06d7afd9b75cb593144fdcc8
i2c_init: by cpux
i2c_init ok
[ 4.468]pmbus: ready
[ 4.487]PMU: AXP221
[ 4.487]PMU: AXP22x found
[ 4.488]PMU: dcdc2 1160
[ 4.489]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100MhzMBus=400Mhz
set power on vol to default
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1160, onoff=1
dcdc3_vol = 1200, onoff=1
dcdc4_vol = 1100, onoff=0
aldo1_vol = 3300, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dc1sw_vol = 3000, onoff=0
dc5ldo_vol = 1100, onoff=0
dldo1_vol = 3300, onoff=1
dldo2_vol = 3300, onoff=0
dldo3_vol = 3300, onoff=0
dldo4_vol = 2500, onoff=1
eldo1_vol = 2800, onoff=0
eldo2_vol = 1200, onoff=1
eldo3_vol = 2800, onoff=1
gpio0_vol = 3300, onoff=1
gpio1_vol = 3300, onoff=1
find power_sply to end
vbus exist
DRAM:512 MiB
fdt addr: 0x56e8fcd8
Relocation Offset is: 15ee6000
In: serial
Out: serial
Err: serial
gic: normal mode
workmode = 16,storage type = 0
[ 4.620]NAND_UbootProbe start
[ 4.623]NB1 : enter phy init
[ 4.626]nand_physic_init
[ 4.742]Reset NDFC start 00
[ 4.742]Reset NDFC end 00
[ 4.743]nand not support! channel 0 chip 0: 00 00 00 00 00 00 00 00
[ 4.749]nand not support! channel 0 chip 1: 00 00 00 00 00 00 00 00
[ 4.755]nand not support! channel 0 chip 2: 00 00 00 00 00 00 00 00
[ 4.762]nand not support! channel 0 chip 3: 00 00 00 00 00 00 00 00
[ 4.768] no nand found !
[ 4.771]nand_physic_init nand_build_nsi error
[ 4.775]nand_physic_init error -1
[ 4.779]NB1 : nand phy init fail
[ 4.782]NB1 : enter phy Exit
[ 4.785]nand_physic_exit
[ 4.788]NAND_UbootProbe end: 0xffffffff
try nand fail
try nand fail
try card 2
: mmc driver ver 2016-07-01 15:50:00
: mmc_update_timing_para: error sdc_no 2
SUNXI SD/MMC: 2
: 50 MHz...
: sample: 63 - 158(ps)
: ds: 63 - 158(ps)
: 100 MHz...
: sample: 33 - 151(ps)
: ds: 32 - 156(ps)
: 200 MHz...
: sample: 16 - 156(ps)
: ds: 16 - 156(ps)
: ************Try SD card 2************
: mmc 2 cmd 8 timeout, err 100
: smc 2 err, cmd 8,RTO
: mmc 2 close bus gating and reset
: mmc 2 mmc cmd 8 err 0x00000100
: mmc send if cond failed
: mmc 2 cmd 55 timeout, err 100
: smc 2 err, cmd 55,RTO
: mmc 2 close bus gating and reset
: mmc 2 mmc cmd 55 err 0x00000100
: send app cmd failed
: ************Try MMC card 2************
: host caps: 0x6f
: MID 0000d6 PSN 8260d1a0
: PNM 88A398 -- 0x38-38-41-33-39
: PRV 1.1
: MDT m-11 y-2021
: MMC v5.1
: speed mode : HSSDR52/SDR25
: clock : 50000000 Hz
: bus_width : 8 bit
: user capacity: 7456 MB
: boot capacity: 4096 KB
: rpmb capacity: 4096 KB
: ************SD/MMC 2 init OK!!!************
: use default speed mode: 1-HSSDR52/SDR25, ifreq: 2
: ========best spd md: 1-HSSDR52/SDR25, freq: 2-50000000
: already at HSSDR52_SDR25 mode
: erase_grp_size : 0x400WrBlk*0x200=0x80000 Byte
: secure_feature : 0x55
: secure_removal_type : 0x9
: EOL Info(Rev blks): Normal
: Wear out(type A): 0%-10% life time used
: Wear out(type B): Not defined
read flash error
[ 5.047]inter uboot shell
Hit any key to stop autoboot:0
work mode=0x10
run usb efex
buf queue page size = 65536
delay time 2500
usb init ok
set address 0x31
set address 0x31 ok
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
the 1 mbr table is ok
the 2 mbr table is ok
the 3 mbr table is ok
*************MBR DUMP***************
total mbr part 6
part name :boot-resource
part classname :DISK
part addrlo :0x8000
part lenlo :0x3800
part user_type :32768
part keydata :0
part ro :0
part name :env
part classname :DISK
part addrlo :0xb800
part lenlo :0x2000
part user_type :32768
part keydata :0
part ro :0
part name :boot
part classname :DISK
part addrlo :0xd800
part lenlo :0x8000
part user_type :32768
part keydata :0
part ro :0
part name :rootfs
part classname :DISK
part addrlo :0x15800
part lenlo :0x200000
part user_type :32768
part keydata :0
part ro :0
part name :usr
part classname :DISK
part addrlo :0x215800
part lenlo :0xcfd800
part user_type :32768
part keydata :0
part ro :0
part name :UDISK
part classname :DISK
part addrlo :0xf13000
part lenlo :0x0
part user_type :0
part keydata :0
part ro :0
total part: 7
mbr 0, 8000, 8000
boot-resource 1, 3800, 8000
env 2, 2000, 8000
boot 3, 8000, 8000
rootfs 4, 200000, 8000
usr 5, cfd800, 8000
UDISK 6, 0, 0
do need erase flash
no part need to protect user data
card2 download boot0
erase boot0, size:32k, write 0x00
erase env part
: erase from: 88064, to: 96255, cnt: 8192, erase_group: 1024
: mmc_send_cmd: cmd 38 wait rsp busy 0xd17 us
erase boot part
: erase from: 96256, to: 129023, cnt: 32768, erase_group: 1024
: mmc_send_cmd: cmd 38 wait rsp busy 0x1568 us
erase rootfs part
: erase from: 129024, to: 2226175, cnt: 2097152, erase_group: 1024
: mmc_send_cmd: cmd 38 wait rsp busy 0x2f847 us
erase usr part
: mmc_mmc_erase: input lenght error!!!
: mmc_mmc_erase: after clip, from: 2226176, nr: 13043712
: erase from: 2226176, to: 15269887, cnt: 13043712, erase_group: 1024
: mmc_send_cmd: cmd 38 wait rsp busy 0x3f77 us
erase UDISK part
sunxi_sprite_mmc_phyerase: @nr is 0, erase from @from to end
: erase from: 15847424, to: 15268863, cnt: -578560, erase_group: 1024
: mmc_send_cmd: cmd 38 wait rsp busy 0x1 us
: mmc_mmc_erase: some sectors in emmc are ignored!
: --0: from15268864nr1023
write zeros-0: from 0xe8fc00 to 0xe8fffe
card erase all
SUNXI_EFEX_MBR_TAG
mbr size = 0x10000
begin to write standard mbr
successed to write standard mbr
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
FEX_CMD_fes_verify_value, start 0x8000, size high 0x0:low 0x530400
FEX_CMD_fes_verify_value 0xbaf04d13
FEX_CMD_fes_verify_value, start 0xb800, size high 0x0:low 0x20000
FEX_CMD_fes_verify_value 0x83a5ca83
FEX_CMD_fes_verify_value, start 0xd800, size high 0x0:low 0xcaa800
FEX_CMD_fes_verify_value 0x67d3d238
FEX_CMD_fes_verify_value, start 0x15800, size high 0x0:low 0x2157e000
FEX_CMD_fes_verify_value 0x100282b
FEX_CMD_fes_verify_value, start 0x215800, size high 0x0:low 0x501600
FEX_CMD_fes_verify_value 0xfa562d1a
bootfile_mode=4
SUNXI_EFEX_BOOT1_TAG
boot1 size = 0x10c000
uboot_pkg magic 0x89119800
uboot size = 0x10c000
storage type = 2
mmc down uboot
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
bootfile_mode=4
SUNXI_EFEX_BOOT0_TAG
boot0 size = 0x8000
: write mmc info ok
dram para = 240
dram para = 3
dram para = 3b3bfb
dram para = 31
dram para = 10e410f4
dram para = 8001000
dram para = 1c70
dram para = 40
dram para = 18
dram para = 0
dram para = 479950
dram para = 1b1a94b
dram para = 65046
dram para = b47d7d96
dram para = 0
dram para = 198
dram para = 21000000
dram para = 2406c1e0
dram para = 0
dram para = 0
dram para = 3
dram para = 33330000
dram para = 7777
dram para = c4096953
dram para = 0
dram para = 0
dram para = 0
dram para = 0
dram para = 0
dram para = 0
dram para = 0
dram para = 0
storage type = 2
card2 download boot0
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
sunxi_efex_next_action=2
exit usb
next work 2
SUNXI_UPDATE_NEXT_ACTION_REBOOT
set next mode 14
disp_ioctl, display not init yet
disp_ioctl, display not init yet
drv_disp_exit
HELLO! BOOT0 is starting!
[ 0.35]HELLO! BOOT0 is starting!
[ 0.39]boot0 commit : b58d49ff80aa5ff8865ab68aa2463d4ee0fe1e7d
[ 0.46]boot0 version : 4.0
[ 0.50]set pll start
[ 0.54]set pll end
[ 0.89]rtc value = 0x00000000
[ 0.92]rtc value = 0x00000000
[ 0.95]rtc value = 0x00000000
[ 0.98]rtc value = 0x00000000
[ 0.102]rtc value = 0x00000000
[ 0.105]rtc value = 0x00000000
[ 0.109]DRAMC IS FOUR
[ 0.111]DRAM BOOT DRIVE INFO: V1.1
[ 0.115]Found A40
[ 0.117]Found A40
[ 0.119]Found A40
[ 0.121]Found A40
[ 0.123]Found A40
[ 0.129]PMU: [ 0.130]AXP221
[ 0.132]ddr voltage = 1500 mv
[ 0.135]DRAM CLK =576 MHZ
[ 0.138]DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
[ 0.143]DRAM zq value: 0x003b3bfb
[ 0.149]DRAM SIZE =2048 M
[ 0.152]DRAM ** test OK.
[ 0.155]dram size =2048
[ 0.157]rtc standby flag is 0x00000000, super standby flag is 0x00000000
[ 0.165]card no is 2
[ 0.167]sdcard 2 line count 8
[ 0.170]: mmc driver ver 2016-07-01 15:30
[ 0.175]: wrong freq 2 at spd md 2
[ 0.188]: ***Try MMC card 2***
[ 0.205]: MMC 5.1
[ 0.207]: HSSDR52/SDR25 8 bit
[ 0.211]: 50000000 Hz
[ 0.213]: 7456 MB
[ 0.216]: ***SD/MMC 2 init OK!!!***
[ 0.289]Succeed in loading uboot from sdmmc flash.
[ 0.293]Entry_name = u-boot
[ 0.309]Ready to disable icache.
[ 0.312]0xffffffff 0xffffffff
[ 0.315]0xffffffff 0xffffffff
[ 0.318]0xffffffff 0xffffffff
[ 0.322]0xffffffff 0xffffffff
[ 0.325]0xffffffff 0xffffffff
[ 0.328]0xffffffff 0xffffffff
[ 0.331]Jump to secend Boot.
U-Boot 2014.07 (Jul 25 2019 - 05:35:06) Allwinner Technology
uboot commit : 65b7504a61af7d8b06d7afd9b75cb593144fdcc8
i2c_init: by cpux
i2c_init ok
[ 0.346]pmbus: ready
[ 0.360]PMU: AXP221
[ 0.360]PMU: AXP22x found
[ 0.361]PMU: dcdc2 1160
[ 0.362]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100MhzMBus=400Mhz
set power on vol to default
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1160, onoff=1
dcdc3_vol = 1200, onoff=1
dcdc4_vol = 1100, onoff=0
aldo1_vol = 3300, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dc1sw_vol = 3000, onoff=0
dc5ldo_vol = 1100, onoff=0
dldo1_vol = 3300, onoff=1
dldo2_vol = 3300, onoff=0
dldo3_vol = 3300, onoff=0
dldo4_vol = 2500, onoff=1
eldo1_vol = 2800, onoff=0
eldo2_vol = 1200, onoff=1
eldo3_vol = 2800, onoff=1
gpio0_vol = 3300, onoff=1
gpio1_vol = 3300, onoff=1
find power_sply to end
vbus exist
run key detect
no key found
no uart input
DRAM:2 GiB
fdt addr: 0xb6e8fcd8
Relocation Offset is: 75ee6000
axp: get node error
In: serial
Out: serial
Err: serial
gic: normal mode
[ 0.516]start
drv_disp_init
init_clocks: finish init_clocks.
pwm_request: reg = 0x1c23400. pwm = 0.
request pwm success, pwm = 0.
tv_init:
tv_probe:000
tv0 have no type1
tv0 have no type2
tv0 have no type3
no report hpd work,you need support the switch class!
screen 0 don't support TV!
screen 1 don't support TV!
screen 0 do not support VGA TYPE!
screen 1 do not support VGA TYPE!
tv_init:
drv_disp_init finish
fetch script data boot_disp.output_disp fail
fetch script data boot_disp.output_type fail
fetch script data boot_disp.output_mode fail
fetch script data boot_disp.auto_hpd fail
disp0 device type(1) enable
disp 0, clk: pll(306000000),clk(306000000),dclk(51000000) dsi_rate(306000000)
clk real:pll(308571428),clk(308571428),dclk(51428571) dsi_rate(0)
enable power vcc-lcd, ret=0
[ 1.279]end
workmode = 0,storage type = 2
[ 1.279]MMC: 2
: mmc driver ver 2016-07-01 15:50:00
: mmc_update_timing_para: error sdc_no 2
SUNXI SD/MMC: 2
: 50 MHz...
: sample: 63 - 158(ps)
: ds: 63 - 158(ps)
: 100 MHz...
: sample: 32 - 156(ps)
: ds: 33 - 151(ps)
: 200 MHz...
: sample: 16 - 156(ps)
: ds: 16 - 156(ps)
: media type 0x8000000
: ************Try MMC card 2************
: host caps: 0x6f
: MID 0000d6 PSN 8260d1a0
: PNM 88A398 -- 0x38-38-41-33-39
: PRV 1.1
: MDT m-11 y-2021
: MMC v5.1
: speed mode : HSSDR52/SDR25
: clock : 50000000 Hz
: bus_width : 8 bit
: user capacity: 7456 MB
: boot capacity: 4096 KB
: rpmb capacity: 4096 KB
: ************SD/MMC 2 init OK!!!************
: use default speed mode: 1-HSSDR52/SDR25, ifreq: 2
: ========best spd md: 1-HSSDR52/SDR25, freq: 2-50000000
: already at HSSDR52_SDR25 mode
: erase_grp_size : 0x400WrBlk*0x200=0x80000 Byte
: secure_feature : 0x55
: secure_removal_type : 0x9
: EOL Info(Rev blks): Normal
: Wear out(type A): 0%-10% life time used
: Wear out(type B): Not defined
[ 1.515]sunxi flash init ok
--------fastboot partitions--------
-total partitions:6-
-name- -start- -size-
boot-resource: 1000000 700000
env : 1700000 400000
boot : 1b00000 1000000
rootfs : 2b00000 40000000
usr : 42b00000 9fb00000
UDISK : e2600000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
no misc partition is found
to be run cmd=run setargs_mmc boot_normal
update dtb dram start
update dtb dramend
PowerBus = 2( 2:vBus 3:acBus other: not exist)
no battery, limit to dc
no battery exist
EnterNormalBootMode sunxi_bmp_display--
reading bootlogo.bmp
1152054 bytes read in 29 ms (37.9 MiB/s)
bmp file buffer: 0x40000000, bmp_info.buffer: 46400000
fetch script data boot_disp.output_full fail
screen_id =0, screen_width =1024, screen_height =600
frame buffer address 46400036
[ 1.774]inter uboot shell
Read addr=40 eeprom addrlen=1 ok!!
The test ok!
secret ok
Hit any key to stop autoboot:0
read partition: boot or recovery
[ 3.106]sunxi flash read :offset 1b00000, 14324561 bytes OK
Android's image name: sun8i_arm
Kernel load addr 0x40008000 size 11613 KiB
RAM disk load addr 0x41000000 size 1353 KiB
[ 3.172]ready to boot
prepare for kernel
: mmc exit start
: 50 MHz...
: sample: 62 - 161(ps)
: ds: 62 - 161(ps)
: 100 MHz...
: sample: 31 - 161(ps)
: ds: 31 - 161(ps)
: 200 MHz...
: sample: 16 - 156(ps)
: ds: 16 - 156(ps)
: mmc 2 exit ok
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.65 (bluesky@a97aa656d1ab) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #39 SMP PREEMPT Mon Jul 29 03:45:11 UTC 2019
[ 0.000000] CPU: ARMv7 Processor revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun8iw11p1, model: sun8iw11p1
[ 0.000000] bootconsole enabled
: RootDevice is "/dev/mmcblk0p7"
: Try to load EMMC ...
e2fsck 1.41.14 (22-Dec-2010)
/dev/mmcblk0p7: clean, 8420/9648 files, 484368/546296 blocks
mount: proc is already mounted or /proc busy
proc is already mounted on /proc
mount: devtmpfs is already mounted or /dev busy
init asteroidenv##
init qt env########################
ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519
Starting sshd: OK
Starting telnetd: OK
Starting vsftpd: OK
================Usrage================
/fbinit means:clean /dev/fb0
/fbinit 0 means:clean /dev/fb0
/fbinit 1 means:clean /dev/fb1
/fbinit 2 means:clean /dev/fb2
================usrage================
cleanning /dev/fb0 ...
clean /dev/fb0 finish
find qt5 installed
D-Bus per-session daemon address is: unix:abstract=/tmp/dbus-CpWXjMg9gl,guid=6f88816b7085eb5221c9379b5e1fdb44
Unknown username "pulse" in message bus configuration file
xres = 1024, yres = 600
create /dev/mmcblk1p1
create /dev/mmcblk1
您的资料太旧了哦，2019年资料只适用于V1.1核心板，您下载最新资料就可以了
页:
[1]