宋强 发表于 2011-3-8 19:30:38

ok6410板子可以一键烧写windowsce 但烧写完linux后 无法启动

用一键烧写linux后 或是用 sd卡烧写完 uboot后，从nand启动后 显示以下信
3c-nand: ECC uncorrectable error detected

s3c-nand: ECC uncorrectable error detected

s3c-nand: ECC uncorrectable error detected

s3c-nand: ECC uncorrectable error detected

s3c-nand: ECC uncorrectable error detected

*** Warning - bad CRC or NAND, using default environment


In:      serial

Out:   serial

Err:   serial

Hit any key to stop autoboot:0

SMDK6410 #
在uboot中用 nand scrub 擦除块后 还是出现这个错误请问这是怎么回事？

飞凌-fatfish 发表于 2011-3-9 08:30:03

用WINCE的EBOOT擦除一下flash吧，A功能就是擦除flash

宋强 发表于 2011-3-9 08:41:11

这个都试过了， uboot中用nand scrub 命令擦除所有块也不管用

宋强 发表于 2011-3-9 10:47:04

现在内核启动了 但由于到了别的错误
cheaking bad block...............
....................................................................................................................................................................................................................................................
bad block at 1e80000
.............
bad block at 2040000
.............................................................................................................................................................................................................................................................................................................................................................................................VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 148K
usb 1-2: new full speed USB device using s3c2410-ohci and address 2
hub 1-0:1.0: unable to enumerate USB device on port 2
mmc0: new high speed SDHC card at address 1234
mmcblk0: mmc0:1234 SA04G 3.68 GiB
mmcblk0: p1
hub 1-0:1.0: connect-debounce failed, port 2 disabled
hub 1-0:1.0: connect-debounce failed, port 2 disabled
hub 1-0:1.0: connect-debounce failed, port 2 disabled
*************************************
   http://www.witech.com.cn      
*************************************
mkdir: cannot create directory '/mnt/disk': File exists
yaffs: dev is 32505859 name is "mtdblock3"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.3, "mtdblock3"
yaffs_read_super: isCheckpointed 0
cp: cannot stat '/mnt/disk/pointercal': No such file or directory
Try to bring eth0 interface up......eth0: link down
Done
                                 
Starting Qtopia, please waiting...
touch...

Please press Enter to activate this console. hub 1-0:1.0: connect-debounce failed, port 2 disabled
hub 1-0:1.0: connect-debounce failed, port 2 disabled
hub 1-0:1.0: connect-debounce failed, port 2 disabled
hub 1-0:1.0: connect-debounce failed, port 2 disabled
hub 1-0:1.0: connect-debounce failed, port 2 disabled
usb 1-2: new full speed USB device using s3c2410-ohci and address 3
usb 1-2: device descriptor read/64, error -62
usb 1-2: device descriptor read/64, error -62
usb 1-2: new full speed USB device using s3c2410-ohci and address 4
usb 1-2: device descriptor read/64, error -62
usb 1-2: device descriptor read/64, error -62
usb 1-2: new full speed USB device using s3c2410-ohci and address 5
usb 1-2: device not accepting address 5, error -62
usb 1-2: new full speed USB device using s3c2410-ohci and address 6
usb 1-2: device not accepting address 6, error -62
hub 1-0:1.0: unable to enumerate USB device on port 2
又不动了

飞凌-fatfish 发表于 2011-3-9 13:17:37

请勿重复发帖

841565682 发表于 2011-3-17 13:59:52

841565682 发表于 2011-3-17 14:15:19

liuhaohao 发表于 2011-3-17 15:58:59

人海过客 发表于 2011-4-19 18:53:52

飞凌-alexlee 发表于 2011-4-20 08:28:57

楼上，你重新开一个帖子，把你的烧写步骤发上来，鉴定一下～

人海过客 发表于 2011-4-30 11:02:46

页: [1]
查看完整版本: ok6410板子可以一键烧写windowsce 但烧写完linux后 无法启动