usd的wifi驱动
本帖最后由 aa2235236 于 2014-12-26 22:55 编辑你好，我在OK210添加了USB的RTL8188的wif，加载了驱动，试了测试程序，发现没有发射出热点，请问是不是内核配置的问题，添加IP地址时打印出下列信息，不知道正确与否，请指教谢谢！
[# /home/wifi]# ifconfig wlan0 192.168.11.1
[ 92.083881] +871x_drv - drv_open, bup=0
[ 92.095099]===> FirmwareDownload91C() fw:Rtl819XFwImageArray_TSMC
[ 92.099904] FirmwareDownload92C accquire FW from embedded image
[ 92.105821] fw_ver=v80, fw_subver=0, sig=0x88c0
[ 92.260319] Polling FW ready fail!! REG_MCUFWDL:0x00030006 .
[ 92.264574] Reset 51 write8 REG_SYS_FUNC_EN:0x00f8
[ 92.269450] Reset 51 write8 REG_SYS_FUNC_EN:0x00fc
[ 92.281574] fw download ok!
[ 92.282881] Set RF Chip ID to RF_6052 and RF type to 1T1R.
[ 92.869571] reg 0x800, usb write 4 fail, status:-110 value=0x80040000, vendorreq_times:1
[ 93.373318] reg 0x800, usb write 4 fail, status:-110 value=0x80040000, vendorreq_times:2
[ 93.877193] reg 0x800, usb write 4 fail, status:-110 value=0x80040000, vendorreq_times:3
[ 94.381194] reg 0x800, usb write 4 fail, status:-110 value=0x80040000, vendorreq_times:4
[ 94.885068] reg 0x800, usb write 4 fail, status:-110 value=0x80040000, vendorreq_times:5
[ 94.891693] continual_urb_error:5 > 4
[ 95.115696] ==>_InitAntenna_Selection ....
[ 95.118480] _InitAntenna_Selection,Cur_ant:(1)Antenna_B
[ 95.123694] IQK:Start!!!
[ 95.127353] Path A IQK Success!!
[ 95.130405] Path A IQK Success!!
[ 95.132626] IQK: final_candidate is 0
[ 95.136263] IQK: RegE94=0 RegE9C=0 RegEA4=0 RegEAC=0 RegEB4=0 RegEBC=0 RegEC4=0 RegECC=0
[ 95.136271]pdmpriv->TxPowerTrackControl = 1
[ 95.249831] MAC Address from REG_MACID = 00:00:00:00:00:00
[ 95.255300] rtl8192cu_hal_init in 3167ms
[ 95.259204] MAC Address = 00:00:30:34:43:30
[ 95.263533] -871x_drv - drv_open, bup=1
[ 95.267419] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[# /home/wifi]# [ 97.267756] ==>pwr_state_check_handler .fw_state(0)
[ 97.271157] ==> rtw_ps_cmd, enqueue CMD
[ 97.275247] ###> rtw_cmd_thread break.................
[ 97.280475] rtw_cmd_thread: leaving... check & free all cmd_obj resources
[ 97.287105] rtw_cmd_thread: leaving... drop cmdcode:57
[ 97.292221] rtw_cmd_thread: leaving... call up terminate_cmdthread_sema
楼主，你是要建立AP热点吗？如果是，请查看手册6.2.33的内容“AP 功能”
页:
[1]