插入SD卡无法识别

wx7years

A40I开发板插入SD卡，启动无法识别，/mnt/sdcard/mmcblk1p1挂载点也没有内容。
内核打印内容如下：

# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.65 (bluesky@a97aa656d1ab) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #357 SMP PREEMPT Sat Dec 5 08:16:51 UTC 2020
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun8iw11p1, model: sun8iw11p1
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] cma: CMA: reserved 60 MiB at 63400000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 262144
[    0.000000] free_area_init_node: node 0, pgdat c0b68bc0, node_mem_map c1153000
[    0.000000]   Normal zone: 1248 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 159744 pages, LIFO batch:31
[    0.000000]   HighMem zone: 800 pages used for memmap
[    0.000000]   HighMem zone: 102400 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 9 pages/cpu @c1979000 s13632 r8192 d15040 u36864
[    0.000000] pcpu-alloc: s13632 r8192 d15040 u36864 alloc=9*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260896
[    0.000000] Kernel command line: enforcing=1 earlyprintk=sunxi-uart,0x01c28000 initcall_debug=0 console=ttyS0,115200 loglevel=0 root=/dev/mmcblk0p7 init=/init partitions=boot-resource@mmcblk0p2:env@mmcblk0p5:boot@mmcblk0p6:rootfs@mmcblk0p7:private@mmcblk0p8:usr@mmcblk0p9:UDISK@mmcblk0p1 cma=60M vmalloc=384MB androidboot.serialno=<NULL> boot_type=2 androidboot.hardware=sun8iw11p1 mac_addr= sn=
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1024MB = 1024MB total
[    0.000000] Memory: 708000k/708000k available, 340576k reserved, 409600K highmem
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
                   vmalloc : 0xe7800000 - 0xff000000   ( 376 MB)
                   lowmem  : 0xc0000000 - 0xe7000000   ( 624 MB)
                   pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
                   modules : 0xbf000000 - 0xbfe00000   (  14 MB)
                     .text : 0xc0008000 - 0xc09cb744   (9998 kB)
                     .init : 0xc09cc000 - 0xc0a3b540   ( 446 kB)
                     .data : 0xc0a3c000 - 0xc0b73ea0   (1248 kB)
                      .bss : 0xc0b73ea0 - 0xc0bfec1c   ( 556 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] of_sunxi_clocks_init : sunxi_clk_base[0xf1c20000]
[    0.000000] pll_audio-set_default_rate=24576000 success!
[    0.000000] pll_periph0-set_default_rate=600000000 success!
[    0.000000] pll_de-set_default_rate=297000000 success!
[    0.000000] ahb1-set_default_rate=200000000 success!
[    0.000000] apb1-set_default_rate=100000000 success!
[    0.000000] apb2-set_default_rate=24000000 success!
[    0.000000] de-set_default_rate=297000000 success!
[    0.000000] de_mp-set_default_rate=297000000 success!
[    0.000000] mbus-set_default_rate=400000000 success!
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
[    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[    0.000000] Console: colour dummy device 80x30
[    0.010000] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.010000] pid_max: default: 32768 minimum: 301
[    0.010000] Mount-cache hash table entries: 512
[    0.010000] Initializing cgroup subsys debug
[    0.010000] Initializing cgroup subsys freezer
[    0.010000] CPU: Testing write buffer coherency: ok
[    0.010000] ftrace: allocating 27043 entries in 80 pages
[    0.030554] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.030601] Setting up static identity map for 0xc06ad280 - 0xc06ad2d8
[    0.010000] CPU1: Booted secondary processor
[    0.010000] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.010000] CPU2: Booted secondary processor
[    0.010000] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.010000] CPU3: Booted secondary processor
[    0.010000] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.032584] Brought up 4 CPUs
[    0.032584] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[    0.032584] devtmpfs: initialized
[    0.041160] pinctrl core: initialized pinctrl subsystem
[    0.042537] NET: Registered protocol family 16
[    0.042537] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.042537] dump_class_init,839, success
[    0.052010] sun8iw11p1-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.070328] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.070328] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.110256] bio: create slab <bio-0> at 0
[    0.110360] pwm module init!
[    0.110422] platform pwm0.6: there is no bind_pwm, set bind_pwm 255!
[    0.110422] platform pwm0.6: there is no dead time, set bind_pwm 255!
[    0.110437] platform pwm1.7: there is no bind_pwm, set bind_pwm 255!
[    0.110449] platform pwm1.7: there is no dead time, set bind_pwm 255!
[    0.120411] SCSI subsystem initialized
[    0.120411] libata version 3.00 loaded.
[    0.120411] usbcore: registered new inte**ce driver usbfs
[    0.120411] usbcore: registered new inte**ce driver hub
[    0.120411] usbcore: registered new device driver usb
[    0.130298] Linux video capture inte**ce: v2.00
[    0.130298] reserved carvout base=0x50600000,sz = 0xfa00000
[    0.253309] Advanced Linux Sound Architecture Driver Initialized.
[    0.253309] ------------[ cut here ]------------
[    0.253309] WARNING: at net/wireless/reg.c:434 regulatory_init+0x84/0x120()
[    0.253309] db.txt is empty, you should update it...
[    0.253309] Modules linked in:

[    0.253309] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 3.10.65 #357
[    0.253309] [<c00178d0>] (unwind_backtrace+0x0/0xe8) from [<c0013fac>] (show_stack+0x20/0x24)
[    0.253309] [<c0013fac>] (show_stack+0x20/0x24) from [<c06a252c>] (dump_stack+0x20/0x28)
[    0.253309] [<c06a252c>] (dump_stack+0x20/0x28) from [<c0023b80>] (warn_slowpath_common+0x5c/0x7c)
[    0.253309] [<c0023b80>] (warn_slowpath_common+0x5c/0x7c) from [<c0023be0>] (warn_slowpath_fmt+0x40/0x48)
[    0.253309] [<c0023be0>] (warn_slowpath_fmt+0x40/0x48) from [<c0a03300>] (regulatory_init+0x84/0x120)
[    0.253309] [<c0a03300>] (regulatory_init+0x84/0x120) from [<c0a031fc>] (cfg80211_init+0x60/0xe0)
[    0.253309] [<c0a031fc>] (cfg80211_init+0x60/0xe0) from [<c000a4d8>] (do_one_initcall+0xa8/0x144)
[    0.253309] [<c000a4d8>] (do_one_initcall+0xa8/0x144) from [<c09ccc94>] (kernel_init_freeable+0x160/0x220)
[    0.253309] [<c09ccc94>] (kernel_init_freeable+0x160/0x220) from [<c069b8d4>] (kernel_init+0x18/0xf0)
[    0.253309] [<c069b8d4>] (kernel_init+0x18/0xf0) from [<c000f918>] (ret_from_fork+0x14/0x20)
[    0.253309] ---[ end trace 767ed2a11da5e5a8 ]---
[    0.253309] cfg80211: Calling CRDA to update world regulatory domain
[    0.253309] [pm]aw_pm_init!
[    0.253309] np name = /soc@01c00000/rtc@01c20400.
[    0.253309] base = f1c20500, len = 4.
[    0.253309] pmu0 does not exist.
[    0.253309] pmu1 does not exist.
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vdd-cpua failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vcc-dram failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vdd-sys failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vdd-cpus failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vcc-lpddr failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vcc-pl failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vcc-io failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vcc-pll failed
[    0.253309] add_sys_pwr_dm: get ldo name  for id: vcc-pc failed
[    0.253309] after inited: sys_mask config = 0x0.
[    0.253309] Warning: can not find np for dynamic_standby_para.
[    0.253309] [pm]valid
[    0.253309] [pm]valid
[    0.253309] [DISP]disp_module_init
[    0.260491] [DISP] boot_disp:0x100
[    0.292460] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.292996] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.293398] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.293798] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.294197] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.294595] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.294993] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.295390] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.295787] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.296185] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.296582] [DISP] disp_sys_script_get_item,line:193:of_find_compatible_node allwinner,sunxi-lcd1 fail
[    0.296595] [DISP] fb_base:0x46400000
[    0.296770] fbinit display_fb_request fb0
[    0.318423] display_fb_request fb0 zorder 3
[    0.318531] fbinit display_fb_request fb1
[    0.323113] display_fb_request fb1 zorder 2
[    0.323166] fbinit display_fb_request fb2
[    0.327327] display_fb_request fb2 zorder 0
[    0.327478] [DISP] lcd_clk_config,line:816:disp 0, clk: pll(306000000),clk(306000000),dclk(51000000) dsi_rate(306000000)
                    clk real:pll(308571428),clk(308571428),dclk(51428571) dsi_rate(0)
[    0.327478] [DISP] disp_sys_power_enable,line:445:some error happen, fail to get regulator vcc-lcd
[    0.327478] [DISP]disp_module_init finish
[    0.330229] enter tr_probe
[    0.330372] exit tr_probe
[    0.330548] Welcome to tv decoder driver
[    0.330711] __tvd_probe_init: v4l2 subdev register.
[    0.330821] V4L2 tvd device registered as video4
[    0.330821] __tvd_probe_init: v4l2 subdev register.
[    0.330821] V4L2 tvd device registered as video5
[    0.330821] __tvd_probe_init: v4l2 subdev register.
[    0.330821] V4L2 tvd device registered as video6
[    0.330821] __tvd_probe_init: v4l2 subdev register.
[    0.330821] V4L2 tvd device registered as video7
[    0.330821] tvd_init end
[    0.330821] TVD_power_enable: some error happen, fail to get regulator vcc-tvin
[    0.330821] [axp221s] chip id detect 0x6 !
[    0.330821] [axp221s] enable dcdc2 dvm.
[    0.350378] sunxi budget cooling probe start !
[    0.350414] CPU freq cooling register Success
[    0.350436] CPU hotplug cooling register Success
[    0.360087] CPU budget cooling register Success
[    0.360720] input: sunxi-ths as /devices/virtual/input/input0
[    0.360720] thermal thermal_zone0: failed to read out thermal zone 0
[    0.360720] Switching to clocksource arch_sys_counter
[    0.384104] FS-Cache: Loaded
[    0.384654] CacheFiles: Loaded
[    0.407567] NET: Registered protocol family 2
[    0.408577] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.408712] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.408828] TCP: Hash tables configured (established 8192 bind 8192)
[    0.408899] TCP: reno registered
[    0.408913] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.408971] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.409344] NET: Registered protocol family 1
[    0.420046] hpd :tvd_num[] = 4,g_status[] =401,tvd_onsingal=0
[    0.428301] Trying to unpack rootfs image as initramfs...
[    0.531790] Freeing initrd memory: 1352K (c1000000 - c1152000)
[    0.532516] lock super standby defaultly!
[    0.532532] lookup_scene_lock_name: new scene lock super_standby
[    0.532540] scene_lock_init name=super_standby
[    0.532550] scene_lock: super_standby, type 5, count 1
[    0.649535] bounce pool size: 64 pages
[    0.650880] jffs2: version 2.2. (NAND) (SUMMARY)  \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.
[    0.651299] fuse init (API version 7.22)
[    0.652195] msgmni has been set to 705
[    0.653582] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.653596] io scheduler noop registered
[    0.653604] io scheduler deadline registered
[    0.653687] io scheduler cfq registered (default)
[    0.654761] OF: no ranges; cannot translate
[    0.654780] OF: no ranges; cannot translate
[    0.655095] OF: no ranges; cannot translate
[    0.655109] OF: no ranges; cannot translate
[    0.656251] failed to get normal led pin assign
[    0.656261] failed to get standby led pin assign
[    0.656325] gpio_pin_1(247) gpio_is_valid
[    0.656612] gpio_pin_2(248) gpio_is_valid
[    0.656860] gpio_pin_3(232) gpio_is_valid
[    0.657096] gpio_pin_4(270) gpio_is_valid
[    0.657345] gpio_pin_5(251) gpio_is_valid
[    0.657581] gpio_pin_6(40) gpio_is_valid
[    0.657811] gpio_pin_7(42) gpio_is_valid
[    0.658040] gpio_pin_8(37) gpio_is_valid
[    0.658279] gpio_pin_9(249) gpio_is_valid
[    0.658632] gpio name is PH23, ret = 0
[    0.658926] gpio name is PH24, ret = 0
[    0.659202] gpio name is PH8, ret = 0
[    0.659489] gpio name is PI14, ret = 0
[    0.659749] gpio name is PH27, ret = 0
[    0.659998] gpio name is PB8, ret = 0
[    0.660286] gpio name is PB10, ret = 0
[    0.660539] gpio name is PB5, ret = 0
[    0.660791] gpio name is PH25, ret = 0
[    0.661148] gpio_init finish with uesd
[    0.661984] uart0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a SUNXI
[    0.662013] sw_console_setup()1343 - console setup baud 115200 parity n bits 8, flow n
[    0.662038] console [ttyS0] enabled, bootconsole disabled
[    0.662905] uart2: ttyS2 at MMIO 0x1c28800 (irq = 35) is a SUNXI
[    0.663651] uart3: ttyS3 at MMIO 0x1c28c00 (irq = 36) is a SUNXI
[    0.664256] uart4: ttyS4 at MMIO 0x1c29000 (irq = 49) is a SUNXI
[    0.664891] uart5: ttyS5 at MMIO 0x1c29400 (irq = 50) is a SUNXI
[    0.665541] uart7: ttyS7 at MMIO 0x1c29c00 (irq = 52) is a SUNXI
[    0.667303] sunxi_scr_probe()1059 - Enter ...
[    0.669444] golden init add awchip lock
[    0.669459] misc dump reg init
[    0.670572] G2D: drv_g2d_init
[    0.670852] G2D: Module initialized.major:245
[    0.682245] brd: module loaded
[    0.688178] loop: module loaded
[    0.688572] at24 4-0051: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[    0.689396] sunxi-wlan wlan.22: wlan_busnum (1)
[    0.689412] sunxi-wlan wlan.22: wlan_power_name (vcc-wifi)
[    0.689424] sunxi-wlan wlan.22: wlan_power_ext_name (wlan_power_ext)
[    0.689437] sunxi-wlan wlan.22: io_regulator_name (vcc-io-wifi)
[    0.689482] sunxi-wlan wlan.22: wlan_regon gpio=225  mul-sel=1  pull=-1  drv_level=-1  data=0
[    0.689530] sunxi-wlan wlan.22: get gpio wlan_hostwake failed
[    0.689541] sunxi-wlan wlan.22: get gpio wlan_clk_gpio failed
[    0.689549] get gpio ls_uboot_power_on failed
[    0.689556] get gpio ls_uboot_lcd_power failed
[    0.689563] get gpio ls_uboot_blk_power failed
[    0.689570] get gpio ls_uboot_lcd_bl_en failed
[    0.689592] sunxi-wlan wlan.22: enable clk
[    0.690683] sunxi-ril probe run ....
[    0.690701] sunxi-ril ril_para.16: ril_power_name (ril_vcc)
[    0.691320] sunxi-ril ril_para.16: check ril_power voltage: 3000000
[    0.691332] sunxi-ril ril_para.16: ril power on success
[    0.691365] sunxi-ril ril_para.16: ril_nstandby gpio=82  mul-sel=1  pull=-1  drv_level=-1  data=0
[    0.691404] sunxi-ril ril_para.16: ril_reset gpio=81  mul-sel=1  pull=-1  drv_level=-1  data=0
[    0.693437] Loading iSCSI transport class v2.0-870.
[    0.695519] rdac: device handler registered
[    0.695605] hp_sw: device handler registered
[    0.695615] emc: device handler registered
[    0.695623] alua: device handler registered
[    0.695633] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[    0.695945] osst :I: Tape driver with OnStream support version 0.99.4
               osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[    0.696885] SCSI Media Changer driver v0.25
[    0.697422] osd: LOADED open-osd 0.2.1
[    0.698053] sunxi-ahci 1c18000.sata: sata_regulator0 "vdd-sata-25"!
[    0.698138] sunxi-ahci 1c18000.sata: sata_regulator1 "vdd-sata-12"!
[    0.699205] sunxi-ahci 1c18000.sata: regulator "vdd-sata-25" voltage set: 2500000 to 2500000!
[    0.700203] sunxi-ahci 1c18000.sata: regulator "vdd-sata-12" voltage set: 1200000 to 1200000!
[    0.700777] sunxi-ahci 1c18000.sata: frequncy of module clk for AHCI: 100000000
[    0.700789] sunxi-ahci 1c18000.sata: frequncy of pll clk for AHCI: 100000000
[    0.770042] sunxi-ahci 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    0.770059] sunxi-ahci 1c18000.sata: forcing PORTS_IMPL to 0x1
[    0.770109] sunxi-ahci 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    0.770127] sunxi-ahci 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[    0.770568] dma_alloc_coherent mem = 0xe3440000, size = 0x16500, mem_dma=0x63440000
[    0.771688] scsi0 : sunxi-ahci
[    0.772342] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c181ff] port 0x100 irq 88
[    0.776702] spi spi0: master is unqueued, this is deprecated
[    0.780379] m25p80 spi0.0: found mr25h256, expected w25q128
[    0.780403] m25p80 spi0.0: mr25h256 (32 Kbytes)
[    0.788138] spi spi2: master is unqueued, this is deprecated
[    0.795937] sun4i-mdio 1c0b080.mdio: no regulator found
[    0.796183] libphy: sun4i_mii_bus: probed
[    0.800958] sun4i-emac 1c0b000.eth: eth0: at f1c0b000, IRQ 87 MAC: 36:c9:e3:f1:b8:05
[    0.801763] usbcore: registered new inte**ce driver asix
[    0.801916] usbcore: registered new inte**ce driver ax88179_178a
[    0.802075] usbcore: registered new inte**ce driver cdc_ether
[    0.802234] usbcore: registered new inte**ce driver net1080
[    0.802381] usbcore: registered new inte**ce driver cdc_subset
[    0.802528] usbcore: registered new inte**ce driver zaurus
[    0.802721] usbcore: registered new inte**ce driver cdc_ncm
[    0.802847] GobiNet: Quectel_WCDMA&LTE_Linux&Android_GobiNet_Driver_V1.3.0
[    0.803007] usbcore: registered new inte**ce driver GobiNet
[    0.803034] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.803273] get ehci0-controller, regulator_io is no nocare
[    0.803338] [sunxi-ehci0]: probe, pdev->name: 1c14000.ehci0-controller, sunxi_ehci: 0xc0be0480, 0x:f1c14000, irq_no:47
[    0.804118] sunxi-ehci 1c14000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.804154] sunxi-ehci 1c14000.ehci0-controller: new USB bus registered, assigned bus number 1
[    0.804709] sunxi-ehci 1c14000.ehci0-controller: irq 71, io mem 0xc03a6c2c
[    0.820041] sunxi-ehci 1c14000.ehci0-controller: USB 0.0 started, EHCI 1.00
[    0.820150] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.820162] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.820174] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.820184] usb usb1: Manufacturer: Linux 3.10.65 ehci_hcd
[    0.820194] usb usb1: SerialNumber: sunxi-ehci
[    0.821135] hub 1-0:1.0: USB hub found
[    0.821167] hub 1-0:1.0: 1 port detected
[    0.821475] [ehci0-controller]: sunxi_usb_disable_ehci
[    0.821486] [sunxi-ehci0]: remove, pdev->name: 1c14000.ehci0-controller, sunxi_ehci: 0xc0be0480
[    0.821508] sunxi-ehci 1c14000.ehci0-controller: remove, state 1
[    0.821527] usb usb1: USB disconnect, device number 1
[    0.822776] sunxi-ehci 1c14000.ehci0-controller: USB bus 1 deregistered
[    0.823651] get ehci1-controller, regulator_io is no nocare
[    0.823711] [sunxi-ehci1]: probe, pdev->name: 1c19000.ehci1-controller, sunxi_ehci: 0xc0be0678, 0x:f1c19000, irq_no:6c
[    0.823764] sunxi-ehci 1c19000.ehci1-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.823793] sunxi-ehci 1c19000.ehci1-controller: new USB bus registered, assigned bus number 1
[    0.824217] sunxi-ehci 1c19000.ehci1-controller: irq 108, io mem 0xc03a6c2c
[    0.840071] sunxi-ehci 1c19000.ehci1-controller: USB 0.0 started, EHCI 1.00
[    0.840163] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.840176] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.840187] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.840197] usb usb1: Manufacturer: Linux 3.10.65 ehci_hcd
[    0.840207] usb usb1: SerialNumber: sunxi-ehci
[    0.841080] hub 1-0:1.0: USB hub found
[    0.841105] hub 1-0:1.0: 1 port detected
[    0.841491] get ehci2-controller, regulator_io is no nocare
[    0.841549] [sunxi-ehci2]: probe, pdev->name: 1c1c000.ehci2-controller, sunxi_ehci: 0xc0be0870, 0x:f1c1c000, irq_no:6e
[    0.841604] sunxi-ehci 1c1c000.ehci2-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.841646] sunxi-ehci 1c1c000.ehci2-controller: new USB bus registered, assigned bus number 2
[    0.842066] sunxi-ehci 1c1c000.ehci2-controller: irq 110, io mem 0xc03a6c2c
[    0.860038] sunxi-ehci 1c1c000.ehci2-controller: USB 0.0 started, EHCI 1.00
[    0.860122] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.860134] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.860145] usb usb2: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.860155] usb usb2: Manufacturer: Linux 3.10.65 ehci_hcd
[    0.860165] usb usb2: SerialNumber: sunxi-ehci
[    0.861030] hub 2-0:1.0: USB hub found
[    0.861054] hub 2-0:1.0: 1 port detected
[    0.861825] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.862083] get ohci0-controller, regulator_io is no nocare
[    0.862178] [sunxi-ohci0]: probe, pdev->name: 1c14000.ohci0-controller, sunxi_ohci: 0xc0bdfca0
[    0.862975] sunxi-ohci 1c14000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.863008] sunxi-ohci 1c14000.ohci0-controller: new USB bus registered, assigned bus number 3
[    0.863051] sunxi-ohci 1c14000.ohci0-controller: irq 72, io mem 0xc03a6c2c
[    0.924058] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.924073] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.924084] usb usb3: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.924094] usb usb3: Manufacturer: Linux 3.10.65 ohci_hcd
[    0.924103] usb usb3: SerialNumber: sunxi-ohci
[    0.925062] hub 3-0:1.0: USB hub found
[    0.925086] hub 3-0:1.0: 1 port detected
[    0.925384] [ohci0-controller]: sunxi_usb_disable_ohci
[    0.925396] [sunxi-ohci0]: remove, pdev->name: 1c14000.ohci0-controller, sunxi_ohci: 0xc0bdfca0
[    0.925407] sunxi-ohci 1c14000.ohci0-controller: remove, state 1
[    0.925428] usb usb3: USB disconnect, device number 1
[    0.926193] sunxi-ohci 1c14000.ohci0-controller: USB bus 3 deregistered
[    0.927068] get ohci1-controller, regulator_io is no nocare
[    0.927158] [sunxi-ohci1]: probe, pdev->name: 1c19000.ohci1-controller, sunxi_ohci: 0xc0bdfe98
[    0.927207] sunxi-ohci 1c19000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.927234] sunxi-ohci 1c19000.ohci1-controller: new USB bus registered, assigned bus number 3
[    0.927277] sunxi-ohci 1c19000.ohci1-controller: irq 96, io mem 0xc03a6c2c
[    0.984047] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.984062] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.984073] usb usb3: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.984083] usb usb3: Manufacturer: Linux 3.10.65 ohci_hcd
[    0.984093] usb usb3: SerialNumber: sunxi-ohci
[    0.985045] hub 3-0:1.0: USB hub found
[    0.985070] hub 3-0:1.0: 1 port detected
[    0.985462] get ohci2-controller, regulator_io is no nocare
[    0.985552] [sunxi-ohci2]: probe, pdev->name: 1c1c000.ohci2-controller, sunxi_ohci: 0xc0be0090
[    0.985603] sunxi-ohci 1c1c000.ohci2-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.985642] sunxi-ohci 1c1c000.ohci2-controller: new USB bus registered, assigned bus number 4
[    0.985684] sunxi-ohci 1c1c000.ohci2-controller: irq 97, io mem 0xc03a6c2c
[    1.044066] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.044080] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.044091] usb usb4: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.044101] usb usb4: Manufacturer: Linux 3.10.65 ohci_hcd
[    1.044111] usb usb4: SerialNumber: sunxi-ohci
[    1.045039] hub 4-0:1.0: USB hub found
[    1.045063] hub 4-0:1.0: 1 port detected
[    1.046121] usbcore: registered new inte**ce driver usb-storage
[    1.046509] usbcore: registered new inte**ce driver usbserial
[    1.046673] usbcore: registered new inte**ce driver ftdi_sio
[    1.046838] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.047190] usbcore: registered new inte**ce driver option
[    1.047346] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.047766] usbcore: registered new inte**ce driver pl2303
[    1.047933] usbserial: USB Serial support registered for pl2303
[    1.048147] usbcore: registered new inte**ce driver cdc_xr_usb_serial
[    1.048155] xr_usb_serial_common: Exar USB UART (serial port) driver
[    1.048995] mousedev: PS/2 mouse device common for all mice
[    1.050265] input: sunxi-keyboard as /devices/virtual/input/input1
[    1.051396] input: sunxi-keypad as /devices/virtual/input/kp0
[    1.052654] input: all_key as /devices/platform/sunxi-ts/input/input3
[    1.055480] rtc-rx8010 2-0032: Update timer was detected
[    1.057031] rtc-rx8010 2-0032: rtc core: registered rx8010 as rtc0
[    1.057229] i2c /dev entries driver
[    1.058635] [OV5640@lex]init_sensor - frame_rate: 0, max_win_size: 11
[    1.059184] [VFE]cci_init end
[    1.059195] [VFE]Welcome to Video Front End driver
[    1.059404] [VFE_DEBUG]Get clk Name:csi_s !
[    1.059417] [VFE_DEBUG]Get clk Name:csi0_m !
[    1.059439] [VFE_DEBUG]Get clk Name:pll_periph0 !
[    1.059454] [VFE_DEBUG]Get clk Name:hosc !
[    1.059472] [VFE_DEBUG]csi core clk = 300000000
[    1.059480] [VFE]csi0 probe end!
[    1.059540] [VFE_DEBUG]Get clk Name:csi_s !
[    1.059552] [VFE_DEBUG]Get clk Name:csi1_m !
[    1.059565] [VFE_DEBUG]Get clk Name:pll_periph0 !
[    1.059578] [VFE_DEBUG]Get clk Name:hosc !
[    1.059586] [VFE_DEBUG]csi core clk = 300000000
[    1.059593] [VFE]csi1 probe end!
[    1.059837] [VFE]csi_init end
[    1.060252] [VFE]sunxi_isp_platform_register end
[    1.060600] [VFE]mipi_init end
[    1.060610] [VFE]flash_init end
[    1.061560] [VFE_DEBUG]vfe_probe
[    1.061625] [VFE]pdev->id = 0
[    1.061632] [VFE]dev->cci_sel = 0
[    1.061638] [VFE]dev->csi_sel = 0
[    1.061644] [VFE]dev->mipi_sel = 0
[    1.061650] [VFE]dev->isp_sel = 0
[    1.061656] [VFE_DEBUG]fetch sys_config
[    1.061663] [VFE_DEBUG]dev->ccm_cfg[0] = e27003d8
[    1.061672] [VFE_DEBUG]dev->ccm_cfg[1] = e27005cc
[    1.061689] [VFE_DEBUG]csi0_dev0_mname = ov5640
[    1.061699] [VFE_DEBUG]csi0_dev0_twi_addr = 78
[    1.061709] [VFE_DEBUG]csi0_dev0_twi_id = 1
[    1.061719] [VFE_DEBUG]csi0_dev0_pos = front
[    1.061729] [VFE_DEBUG]csi0_dev0_isp_used = 0
[    1.061738] [VFE_DEBUG]csi0_dev0_fmt = 0
[    1.061748] [VFE_DEBUG]csi0_dev0_stby_mode = 0
[    1.061758] [VFE_DEBUG]csi0_dev0_vflip = 0
[    1.061767] [VFE_DEBUG]csi0_dev0_hflip = 0
[    1.061778] [VFE_WARN]fetch csi0_dev0_iovdd from device_tree failed
[    1.061789] [VFE_DEBUG]csi0_dev0_iovdd_vol = 2ab980
[    1.061800] [VFE_WARN]fetch csi0_dev0_avdd from device_tree failed
[    1.061810] [VFE_DEBUG]csi0_dev0_avdd_vol = 2ab980
[    1.061821] [VFE_WARN]fetch csi0_dev0_dvdd from device_tree failed
[    1.061832] [VFE_DEBUG]csi0_dev0_dvdd_vol = 16e360
[    1.061843] [VFE_WARN]fetch csi0_dev0_afvdd from device_tree failed
[    1.061853] [VFE_DEBUG]csi0_dev0_afvdd_vol = 2ab980
[    1.061866] [VFE_WARN]fetch csi0_dev0_power_en from device_tree failed
[    1.061892] [VFE_DEBUG]csi0_dev0_reset: pin=38  mul-sel=1  drive=0  pull=1  data=0 gnum=38
[    1.061910] [VFE_DEBUG]csi0_dev0_pwdn: pin=39  mul-sel=1  drive=0  pull=1  data=0 gnum=39
[    1.061922] [VFE_DEBUG]csi0_dev0_flash_used = 0
[    1.061933] [VFE_DEBUG]csi0_dev0_flash_type = 2
[    1.061945] [VFE_WARN]fetch csi0_dev0_flash_en from device_tree failed
[    1.061957] [VFE_WARN]fetch csi0_dev0_flash_mode from device_tree failed
[    1.061968] [VFE_WARN]fetch csi0_dev0_flvdd from device_tree failed
[    1.061980] [VFE_WARN]fetch csi0_dev0_flvdd_vol from device_tree failed
[    1.061992] [VFE_WARN]fetch csi0_dev0_af_pwdn from device_tree failed
[    1.062002] [VFE_DEBUG]csi0_dev0_act_used = 0
[    1.062013] [VFE_DEBUG]csi0_dev0_act_name = ad5820_act
[    1.062023] [VFE_DEBUG]csi0_dev0_act_slave = 18
[    1.062032] [VFE_DEBUG]csi0_sensor_list = 1
[    1.062047] [VFE_DEBUG]csi0_mck: pin=129  mul-sel=1  drive=0  pull=1  data=0 gnum=129
[    1.062061] [VFE]fetch front sensor list info start!
[    1.062070] [VFE]Fetch sensor list form"/system/etc/hawkview/sensor_list_cfg.ini"
[    1.120494] ata1: SATA link down (SStatus 0 SControl 300)
[    1.144206] [vfe_warn]open file failed!
[    1.201445] [VFE]fetch front sensor list info end!
[    1.201468] [VFE_DEBUG]dev->ccm_cfg[0]->ccm = ov5640
[    1.201476] [VFE_DEBUG]dev->ccm_cfg[0]->twi_id = 1
[    1.201483] [VFE_DEBUG]dev->ccm_cfg[0]->i2c_addr = 78
[    1.201491] [VFE_DEBUG]dev->ccm_cfg[0]->is_isp_used = 0
[    1.201498] [VFE_DEBUG]dev->ccm_cfg[0]->is_bayer_raw = 0
[    1.201505] [VFE_DEBUG]dev->ccm_cfg[0]->vflip = 0
[    1.201512] [VFE_DEBUG]dev->ccm_cfg[0]->hflip = 0
[    1.201519] [VFE_DEBUG]dev->ccm_cfg[0]->iovdd_str =
[    1.201526] [VFE_DEBUG]dev->ccm_cfg[0]->avdd_str =
[    1.201533] [VFE_DEBUG]dev->ccm_cfg[0]->dvdd_str =
[    1.201540] [VFE_DEBUG]dev->ccm_cfg[0]->afvdd_str =
[    1.201547] [VFE_DEBUG]dev->ccm_cfg[0]->flvdd_str =
[    1.201554] [VFE_DEBUG]dev->ccm_cfg[0]->flash_used = 0
[    1.201561] [VFE_DEBUG]dev->ccm_cfg[0]->act_used = 0
[    1.201568] [VFE_DEBUG]dev->ccm_cfg[0]->act_name = ad5820_act
[    1.201575] [VFE_DEBUG]dev->ccm_cfg[0]->act_slave = 0x18
[    1.201583] [VFE_DEBUG]get irq resource
[    1.201722] [VFE_DEBUG]clock resource
[    1.201731] [VFE_DEBUG]get pin resource
[    1.202270] [VFE]vfe_init end
[    1.202550] usbcore: registered new inte**ce driver uvcvideo
[    1.202559] USB Video Class driver (v1.0.25_SONiX_v3.10.56)
[    1.202565] sunxi cedar version 0.1
[    1.202706] VE: install start!!!

[    1.202779] cedar_ve: cedar-ve the get irq is 85
[    1.203385] VE: get debugfs_mpp_root is NULL, please check mpp

[    1.203397] VE: sunxi ve debug register driver failed!

[    1.204607] input: axp22-powerkey as /devices/soc.0/1c2ac00.twi/i2c-0/0-0034/axp22-powerkey/input/input4
[    1.210056] [VFE]probe_work_handle start!
[    1.210068] [VFE_DEBUG]v4l2_device_register
[    1.210215] [VFE_DEBUG]v4l2 subdev register
[    1.210236] [VFE]vfe_runtime_resume
[    1.221369] sunxi gpu cooling probe start !
[    1.221394] CPU gpu cooling register Success
[    1.222406] [VFE]..........................vfe clk open!.......................
[    1.222429] [VFE_DEBUG]csi_misc_clk is null
[    1.222444] [VFE]v4l2 subdev register input_num = 0
[    1.222453] [VFE]vfe sensor detect start! input_num = 0
[    1.222464] [VFE]Find sensor name is "ov5640", i2c address is 78, type is "YUV" !
[    1.222472] [VFE]Sub device register "ov5640" i2c_addr = 0x78 start!
[    1.222647] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.223153] device-mapper: uevent: version 1.0.3
[    1.223670] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    1.225919] [OV5640@lex]sensor_probe - frame_rate: 0
[    1.225945] [VFE]registered sensor subdev is OK!
[    1.225954] [VFE_DEBUG]ccm_cfg pt = e27003d8
[    1.225961] [VFE_DEBUG]ccm_cfg->sd = e26c4080
[    1.225967] [VFE_DEBUG]module is_isp_used = 0 is_bayer_raw= 0
[    1.225973] [VFE]Check sensor!
[    1.227385] cpuidle: using governor ladder
[    1.227394] cpuidle: using governor menu
[    1.228675] sunxi-mmc 1c11000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.56 2016-06-28 17:01) Compiled in Dec  1 2020 at 01:03:45
[    1.228727] sunxi-mmc 1c11000.sdmmc: regulator prop vmmc,str vcc-emmcv
[    1.228740] sunxi-mmc 1c11000.sdmmc: regulator prop vqmmc,str vcc-emmcvq18
[    1.228751] sunxi-mmc 1c11000.sdmmc: regulator prop vdmmc,str none
[    1.228873] sunxi-mmc 1c11000.sdmmc: No vdmmc regulator found
[    1.229669] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 22 width 1 timing LEGACY(SDR12) dt B
[    1.238016] [OV5640@lex]CSI_SUBDEV_PWR_ON!
[    1.239271] [VFE]mclk on
[    1.250042] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    1.262051] [VFE_DEBUG]os_gpio_write, hdl is INVALID
[    1.270122] sunxi-mmc 1c11000.sdmmc: base:0xf1c11000 irq:66
[    1.270625] sunxi-mmc 1c0f000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.56 2016-06-28 17:01) Compiled in Dec  1 2020 at 01:03:45
[    1.270664] sunxi-mmc 1c0f000.sdmmc: regulator prop vmmc,str vcc-sdcv-p3
[    1.270676] sunxi-mmc 1c0f000.sdmmc: regulator prop vqmmc,str vcc-sdcvq33-p3
[    1.270687] sunxi-mmc 1c0f000.sdmmc: regulator prop vdmmc,str vcc-sdcvd-p3
[    1.270929] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 52, RTO !!
[    1.271368] sunxi-mmc 1c0f000.sdmmc: Got CD GPIO #267.
[    1.271730] sunxi-mmc 1c0f000.sdmmc: base:0xf1c0f000 irq:64
[    1.271780] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 52, RTO !!
[    1.271815] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    1.272241] sunxi-mmc 1c10000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.56 2016-06-28 17:01) Compiled in Dec  1 2020 at 01:03:45
[    1.272268] sunxi-mmc 1c10000.sdmmc: ***ctl-spec-caps*** 1
[    1.272284] sunxi-mmc 1c10000.sdmmc: Can't get vmmc regulator string
[    1.272293] sunxi-mmc 1c10000.sdmmc: Can't get vqmmc regulator string
[    1.272303] sunxi-mmc 1c10000.sdmmc: Can't get vdmmc regulator string
[    1.272308] get() with no identifier
[    1.272314] get() with no identifier
[    1.272318] get() with no identifier
[    1.272326] sunxi-mmc 1c10000.sdmmc: No vmmc regulator found
[    1.272334] sunxi-mmc 1c10000.sdmmc: No vqmmc regulator found
[    1.272341] sunxi-mmc 1c10000.sdmmc: No vdmmc regulator found
[    1.272979] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.274267] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    1.276159] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 8, RTO !!
[    1.276999] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 5, RTO !!
[    1.277833] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 5, RTO !!
[    1.278668] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 5, RTO !!
[    1.279503] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 5, RTO !!
[    1.280342] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 55, RTO !!
[    1.281181] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 55, RTO !!
[    1.282016] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 55, RTO !!
[    1.282851] sunxi-mmc 1c11000.sdmmc: smc 0 p2 err, cmd 55, RTO !!
[    1.282877] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    1.283249] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B
[    1.283300] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B
[    1.283350] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B
[    1.285762] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B
[    1.290037] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    1.305112] [VFE_DEBUG]power_on______________________________
[    1.305122] [OV5640@lex]sensor_init: 0x0
[    1.305318] sunxi_i2c_do_xfer()902 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x3c)
[    1.305328] [VFE_DEV_I2C_ERR]cci_read_a16_d8 error! slave = 0x3c, addr = 0x300a, value = 0x 0

[    1.305513] sunxi_i2c_do_xfer()902 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x3c)
[    1.305522] [VFE_DEV_I2C_ERR]cci_read_a16_d8 error! slave = 0x3c, addr = 0x300a, value = 0x 0

[    1.305705] sunxi_i2c_do_xfer()902 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x3c)
[    1.305714] [VFE_DEV_I2C_ERR]cci_read_a16_d8 error! slave = 0x3c, addr = 0x300a, value = 0x 0
                ov5640 sensor read retry=2
[    1.305723] [OV5640@lex]error at sensor_detect
[    1.305729] [OV5640@lex]chip found is not an target chip.
[    1.305736] [OV5640@lex]CSI_SUBDEV_PWR_OFF!
[    1.305741] [VFE]mclk off
[    1.310114] sunxi-mmc 1c10000.sdmmc: base:0xf1c10000 irq:65
[    1.310682] sunxi-mmc 1c12000.sdmmc: SD/MMC/SDIO Host Controller Driver(v0.56 2016-06-28 17:01) Compiled in Dec  1 2020 at 01:03:45
[    1.310708] sunxi-mmc 1c12000.sdmmc: ***ctl-spec-caps*** 1
[    1.310740] sunxi-mmc 1c12000.sdmmc: regulator prop vmmc,str vcc-sdcv-p3
[    1.310752] sunxi-mmc 1c12000.sdmmc: regulator prop vqmmc,str vcc-sdcvq33-p3
[    1.310763] sunxi-mmc 1c12000.sdmmc: regulator prop vdmmc,str vcc-sdcvd-p3
[    1.310798] axp22_dcdc1: Failed to create debugfs directory
[    1.310812] axp22_dcdc1: Failed to create debugfs directory
[    1.310826] axp22_dcdc1: Failed to create debugfs directory
[    1.311256] sunxi-mmc 1c12000.sdmmc: Got CD GPIO #266.
[    1.311600] sunxi-mmc 1c12000.sdmmc: base:0xf1c12000 irq:67
[    1.312456] hidraw: raw HID events driver (C) Jiri Kosina
[    1.313048] usbcore: registered new inte**ce driver usbhid
[    1.313056] usbhid: USB HID core driver
[    1.313775] zram: Created 1 device(s) ...
[    1.314488] ashmem: initialized
[    1.314816] logger: created 256K log 'log_main'
[    1.315091] logger: created 256K log 'log_events'
[    1.315365] logger: created 256K log 'log_radio'
[    1.315637] logger: created 256K log 'log_system'
[    1.317637] headphonevol:59, spkervol:27, maingain:4, pa_sleep_time:350
[    1.317833] [VFE_DEBUG]os_gpio_write, hdl is INVALID
[    1.321327] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 7 width 1 timing LEGACY(SDR12) dt B
[    1.323355] sunxi-codec-machine sound.3:  sun8iw11codec <-> 1c22c00.cpudai0-controller mapping ok
[    1.326737] sndhdmi sound.4:  sndhdmi <-> 1c22800.daudio mapping ok
[    1.328477] u32 classifier
[    1.328487]     Actions configured
[    1.328498] Netfilter messages via NETLINK v0.30.
[    1.328511] nfnl_acct: registering with nfnetlink.
[    1.328592] nf_conntrack version 0.5.0 (12043 buckets, 48172 max)
[    1.328976] ctnetlink v0.93: registering with nfnetlink.
[    1.329875] xt_time: kernel timezone is -0000
[    1.330055] ipip: IPv4 over IPv4 tunneling driver
[    1.331954] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.332134] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[    1.332186] arp_tables: (C) 2002 David S. Miller
[    1.332243] TCP: bic registered
[    1.332250] TCP: cubic registered
[    1.332256] TCP: westwood registered
[    1.332262] TCP: htcp registered
[    1.332267] Initializing XFRM netlink socket
[    1.332557] NET: Registered protocol family 10
[    1.333407] mip6: Mobile IPv6
[    1.333416] sit: IPv6 over IPv4 tunneling driver
[    1.333957] mmc0: BKOPS_EN bit is not set
[    1.335085] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 7 width 1 timing MMC-HS(SDR20) dt B
[    1.335085] NET: Registered protocol family 17
[    1.335126] NET: Registered protocol family 15
[    1.335135] 8021q: 802.1Q VLAN Support v1.8
[    1.335193] mmc0: Check switch ready sunxi_mmc_check_timing_switch_done
[    1.335541] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 7 width 1 timing MMC-HS(SDR20) dt B
[    1.335640] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    1.335730] sunxi-mmc 1c11000.sdmmc: sdc set ios: clk 50000000Hz bm PP pm ON vdd 7 width 8 timing MMC-HS(SDR20) dt B
[    1.336987] mmc0: new high speed MMC card at address 0001
[    1.337325] [DISP] boot_disp:0x100
[    1.337533] mmcblk0: mmc0:0001 88A378 7.28 GiB
[    1.337737] mmcblk0boot0: mmc0:0001 88A378 partition 1 4.00 MiB
[    1.337918] mmcblk0boot1: mmc0:0001 88A378 partition 2 4.00 MiB
[    1.339144] [HDMI] cec support = 0
[    1.340067] [VFE_DEBUG]power_off______________________________
[    1.340076] [VFE]vfe sensor subdev unregister!
[    1.340197] [OV5640@lex]sensor_remove ov5640 sd = e26c4080!
[    1.340361] [VFE]Sub device register "ov5640" failed!
[    1.340371] [VFE_ERR]vfe sensor register check error at input_num = 0
[    1.340378] [VFE_DEBUG]dev->ccm_cfg[0] = e27003d8
[    1.340385] [VFE_DEBUG]dev->ccm_cfg[0]->sd =   (null)
[    1.340391] [VFE_DEBUG]dev->ccm_cfg[0]->power.iovdd =   (null)
[    1.340397] [VFE_DEBUG]dev->ccm_cfg[0]->power.avdd =   (null)
[    1.340404] [VFE_DEBUG]dev->ccm_cfg[0]->power.dvdd =   (null)
[    1.340410] [VFE_DEBUG]dev->ccm_cfg[0]->power.afvdd =   (null)
[    1.340420] [VFE]V4L2 device registered as (null)
[    1.340456] [VFE]vfe_runtime_suspend
[    1.340463] [VFE]..........................vfe clk close!.......................
[    1.340477] [VFE_DEBUG]csi_misc_clk is null
[    1.346675] [VFE]probe_work_handle end!
[    1.366755]  mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 >
[    1.366783] mmcblk0: p1 start 16647424 is beyond EOD, truncated
[    1.367789] mmcblk0: p9 size 12525568 extends beyond EOD, truncated
[    1.370542]  mmcblk0boot1: unknown partition table
[    1.372220]  mmcblk0boot0: unknown partition table
[    1.441284] tve0 have no dac 1
[    1.441299] tve0 have no type1
[    1.441306] tve0 have no dac 2
[    1.441313] tve0 have no type2
[    1.441320] tve0 have no dac 3
[    1.441327] tve0 have no type3
[    1.441334] [DISP] boot_disp:0x100
[    1.441758] [DISP] disp_init_tv,line:641:screen 0 don't support TV!
[    1.441768] [DISP] disp_init_tv,line:641:screen 1 don't support TV!
[    1.441828] [DISP] disp_init_tv,line:651:disp1 not support tv
[    1.441841] [DISP] disp_init_vga,line:616:screen 0 do not support VGA TYPE!
[    1.441850] [DISP] disp_init_vga,line:616:screen 1 do not support VGA TYPE!
[    1.441875] [DISP] disp_init_vga,line:632:disp0 not support vga
[    1.441899] [DISP] disp_init_vga,line:625:disp1 not support vga
[    1.449449] usb_serial_number:20080411
[    1.451159] file system registered
[    1.462060] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.462076] android_usb gadget: Number of LUNs=3
[    1.462084]  lun0: LUN: removable file: (no medium)
[    1.462092]  lun1: LUN: removable file: (no medium)
[    1.462099]  lun2: LUN: removable file: (no medium)
[    1.464110] android_usb gadget: android_usb ready
[    1.466037] rtc-rx8010 2-0032: setting system clock to 2021-08-23 16:46:14 UTC (1629737174)
[    1.471070] ALSA device list:
[    1.471093]   #0: audiocodec
[    1.471099]   #1: sndhdmi
[    1.471898] Freeing unused kernel memory: 444K (c09cc000 - c0a3b000)
[    1.516731] EXT4-fs (mmcblk0p7): barriers disabled
[    1.518429] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,barrier=0,data=ordered
[    1.635747] EXT4-fs (mmcblk0p7): re-mounted. Opts: (null)
[    1.803157] udevd[1198]: starting eudev-3.2
[    2.204749] ***CTP***GTP driver init
[    2.204900] ctp_fetch_sysconfig_para: ctp_power_io is invalid.
[    2.205902] get ctp_screen_max_x is fail, -22
[    2.220028] ***CTP***info.ctp_used:1
[    2.220037] ***CTP***info.twi_id:3
[    2.220043] ***CTP***info.screen_max_x:1024
[    2.220049] ***CTP***info.screen_max_y:600
[    2.220054] ***CTP***info.touch_panel_max_x:800
[    2.220059] ***CTP***info.touch_panel_max_y:480
[    2.220065] ***CTP***info.revert_x_flag:1
[    2.220070] ***CTP***info.revert_y_flag:1
[    2.220075] ***CTP***info.exchange_x_y_flag:0
[    2.220080] ***CTP***info.irq_gpio_number:239
[    2.220085] ***CTP***info.wakeup_gpio_number:238
[    2.220094] ***CTP******CTP*** ctp_wakeup:status:0,ms = 0
[    2.290129] ***CTP******CTP*** ctp_wakeup:status:1,ms = 0
[    2.390734] the adapter number is 0
[    2.390755] the adapter number is 1
[    2.390764] the adapter number is 2
[    2.390772] the adapter number is 3
[    2.390779] ctp_detect: addr = 5d
[    2.391035] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.391233] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.391419] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.391604] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.391789] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.391798] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    2.391804] <<-GTP-INFO->> Guitar reset
[    2.510164] <<-GTP-ERROR->> GTP i2c test failed time 1.
[    2.530502] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.530709] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.531070] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.531321] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.531682] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.531701] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    2.531707] <<-GTP-INFO->> Guitar reset
[    2.650135] <<-GTP-ERROR->> GTP i2c test failed time 2.
[    2.670338] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.670742] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.670954] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.671319] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.671530] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.671540] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    2.671545] <<-GTP-INFO->> Guitar reset
[    2.790184] <<-GTP-ERROR->> GTP i2c test failed time 3.
[    2.810503] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.810712] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.811074] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.811286] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.811649] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.811669] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    2.811676] <<-GTP-INFO->> Guitar reset
[    2.930186] <<-GTP-ERROR->> GTP i2c test failed time 4.
[    2.950515] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.950731] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.951104] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.951324] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.951698] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    2.951718] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    2.951724] <<-GTP-INFO->> Guitar reset
[    3.021220] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.022210] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.022319] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.024945] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.026953] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 8, RTO !!
[    3.027943] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.028997] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.029983] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.031050] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.032043] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.033104] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.034094] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.035154] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.035270] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.036254] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 1, RTO !!
[    3.036364] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.037450] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.050169] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.070189] <<-GTP-ERROR->> GTP i2c test failed time 5.
[    3.071236] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.072541] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.072651] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.075248] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 300000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.077403] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 8, RTO !!
[    3.078513] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.079620] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.080860] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.082053] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.083163] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.084270] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.085373] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.086476] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.086505] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 300000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.087690] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 1, RTO !!
[    3.087717] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.088798] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.090071] detect ret -70
[    3.090078] ======detect ok !=====
[    3.090342] ***CTP***GTP Driver Version: V2.2<2014/01/14>***CTP***GTP Driver Built@01:03:36, Dec  1 2020***CTP***GTP I2C Address: 0x5d
[    3.090883] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.091271] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.091859] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.092238] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.092601] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.092624] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    3.092631] <<-GTP-INFO->> Guitar reset
[    3.100191] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.121671] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.123323] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.123351] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.126162] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 200000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.128874] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 8, RTO !!
[    3.130520] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.132164] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.133804] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.135444] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.137089] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.138729] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.140406] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.142159] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.142266] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 200000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.144055] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 1, RTO !!
[    3.144160] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.145255] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.160106] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 150000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.182258] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.184545] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 52, RTO !!
[    3.184649] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 150000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.187897] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 150000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.191243] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 8, RTO !!
[    3.193484] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.195771] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.198127] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.200385] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 5, RTO !!
[    3.202599] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.204859] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.207039] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.209218] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 55, RTO !!
[    3.209252] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 150000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.210170] <<-GTP-ERROR->> GTP i2c test failed time 1.
[    3.211695] sunxi-mmc 1c10000.sdmmc: smc 2 p1 err, cmd 1, RTO !!
[    3.211802] sunxi-mmc 1c10000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    3.230667] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.230875] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.231234] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.231638] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.231843] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.231852] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    3.231858] <<-GTP-INFO->> Guitar reset
[    3.350181] <<-GTP-ERROR->> GTP i2c test failed time 2.
[    3.370545] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.370751] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.371111] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.371322] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.371680] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.371700] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    3.371706] <<-GTP-INFO->> Guitar reset
[    3.490186] <<-GTP-ERROR->> GTP i2c test failed time 3.
[    3.510499] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.510704] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.511062] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.511269] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.511627] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.511646] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    3.511652] <<-GTP-INFO->> Guitar reset
[    3.630195] <<-GTP-ERROR->> GTP i2c test failed time 4.
[    3.650419] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.650798] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.651009] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.651386] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.651598] sunxi_i2c_do_xfer()902 - [i2c3] incomplete xfer (status: 0x20, dev addr: 0x5d)
[    3.651607] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset.
[    3.651613] <<-GTP-INFO->> Guitar reset
[    3.770196] <<-GTP-ERROR->> GTP i2c test failed time 5.
[    3.790133] I2C communication ERROR!
[    3.790175] gt9xxnew_ts: probe of 3-005d failed with error -70
[    3.790210] the adapter number is 4
[    4.330392] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    4.420057]
               insmod_device_driver

[    4.503680] Mali: Enable gpu power successfully.
[    4.503766] Mali: Set gpu frequency to 384 MHz
[    4.503836] Mali: Mali GPU initialization finished.
[    4.920092] *mmc1 detect cd change*
[    4.920113] *mmc1 lock*
[    4.920140] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm PP pm UP vdd 22 width 1 timing LEGACY(SDR12) dt B
[    4.940137] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    4.960965] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 52, RTO !!
[    4.961942] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 52, RTO !!
[    4.962041] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    4.964648] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm PP pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    4.966647] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 8, RTO !!
[    4.967625] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 5, RTO !!
[    4.968598] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 5, RTO !!
[    4.969571] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 5, RTO !!
[    4.970530] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 5, RTO !!
[    4.971504] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    4.972479] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    4.973454] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    4.974372] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 55, RTO !!
[    4.974405] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 400000Hz bm OD pm ON vdd 22 width 1 timing LEGACY(SDR12) dt B
[    4.975442] sunxi-mmc 1c0f000.sdmmc: smc 1 p0 err, cmd 1, RTO !!
[    4.975542] sunxi-mmc 1c0f000.sdmmc: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    5.428786] gpu cooling callback register Success
[    5.428804] Mali: Mali device driver loaded
[    5.986202]  fbid=0 uiid=0
[    5.986220] [DISP] sunxi_fb_to_display,line:590:sunxi_fb_to_display fb0 UIid 0
[    5.986235] [DISP] sunxi_fb_to_display,line:653:sunxi_fb_to_display set fb0 UIid 0 chan[1]lid[0]z[3]
[    5.988914] input procname=Launcher
[    7.486235] [DISP] disp_get_layer,line:67:disp_get_layer (0,-521256960,0) fail
[    7.499853] [DISP] disp_get_layer,line:67:disp_get_layer (0,-520937472,0) fail
[    7.499891] [DISP] disp_get_layer,line:67:disp_get_layer (0,-521248768,0) fail
[    8.013043] dump_store,698 err, invalid para!
[    8.119738] dump_store,698 err, invalid para!
[    8.122419] dump_store,698 err, invalid para!
[    8.126509] dump_store,698 err, invalid para!
[    8.130476] dump_store,698 err, invalid para!
[    8.334428] vidioc_g_fmt_vid_cap: signal is not locked.
[    8.342676] dump_store,698 err, invalid para!
[    8.520065] hpd :tvd_num[] = 4,g_status[] =400,tvd_onsingal=0
[    8.545471] vidioc_g_fmt_vid_cap: signal is not locked.
[    8.551013] dump_store,698 err, invalid para!
[    8.753765] vidioc_g_fmt_vid_cap: signal is not locked.
[    8.759742] dump_store,698 err, invalid para!
[    8.820086] hpd :tvd_num[] = 5,g_status[] =500,tvd_onsingal=0
[    8.920087] hpd :tvd_num[] = 6,g_status[] =600,tvd_onsingal=0
[    8.963098] vidioc_g_fmt_vid_cap: signal is not locked.
[    9.220051] hpd :tvd_num[] = 7,g_status[] =700,tvd_onsingal=0
[    9.281866] vidioc_g_fmt_vid_cap: signal is not locked.
[    9.348728] EXT4-fs (mmcblk0p9): mounted filesystem without journal. Opts: (null)
[    9.388445]
               rmmod_device_driver

[    9.388525] android_work: did not send uevent (0 0   (null))
[    9.388588]
               insmod_device_driver

[    9.389491] android_usb: already disabled
[    9.423876] adb_open
[    9.423920] adb_bind_config
[    9.485377] vidioc_g_fmt_vid_cap: signal is not locked.
[    9.688682] vidioc_g_fmt_vid_cap: signal is not locked.
[    9.892355] vidioc_g_fmt_vid_cap: signal is not locked.
[   10.158208] dump_store,698 err, invalid para!
[   10.350139] gpu cooling callback set freq limit 384



采用的SD卡是

zhichao

我看打印信息里没有mmcblk1相关的信息，应该是没识别SD卡，您检查一下硬件连接吧，另外SD卡一般选fat32格式

wx7years

zhichao 发表于 2021-8-24 09:27
我看打印信息里没有mmcblk1相关的信息，应该是没识别SD卡，您检查一下硬件连接吧，另外SD卡一般选fat32格式

SD卡是格式化成的fat32格式，硬件连接的话，我只能测试几个管脚电压，检测管脚电压为0，其余几个上拉的为3.3v，按我的理解来说应该是对的