- 积分
- 212
贡献1211
飞刀448 FD
注册时间2017-9-8
在线时间58 小时
扫一扫,手机访问本帖
|
U-Boot 2015.04-g3989e3c (Dec 14 2017 - 19:11:47)
CPU: Freescale i.MX6UL rev1.1 at 396 MHz
CPU: Temperature 40 C
Reset cause: POR
Board: MX6UL 14x14 EVK
I2C: ready
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
Display: TFT70AB (800x480)
Video: 800x480x24
Error: no valid bmp image at 83800000 cfb_console.c
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc0 is current device
Net: Phy 2 not found
PHY reset timed out
FEC0
Error: FEC0 address not set.
Normal Boot
Hit any key to stop autoboot: 0
reading boot.scr
** Unable to read file boot.scr **
update emmc.........
reading /bin/zImage
6219672 bytes read in 567 ms (10.5 MiB/s)
reading /bin/ramdisk.img.u
8158014 bytes read in 736 ms (10.6 MiB/s)
reading /bin/imx6ul-14x14-evk.dtb
38346 bytes read in 24 ms (1.5 MiB/s)
Kernel image @ 0x80800000 [ 0x000000 - 0x5ee798 ]
## Loading init Ramdisk from Legacy Image at 83800000 ...
Image Name: ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8157950 Bytes = 7.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 8300c5c9
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.38-6UL_ga-gd42029a (liyue@developer-RH2485-V2) (gcc version 4.6.2 20110630 (prerelease) (Freescale MAD -- Linaro 2011.07 -- Built at 2011/08/10 09:20) ) #2 SMP PREEMPT Tue Aug 8 08:24:30 CST 2017
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board
[ 0.000000] cma: CMA: reserved 64 MiB at 8c000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 8 pages/cpu @8bdbf000 s8320 r8192 d16256 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttymxc0,115200 cma=64M rdinit=/linuxrc
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 174440K/262144K available (7657K kernel code, 452K rwdata, 2696K rodata, 388K init, 433K bss, 87704K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0x90800000 - 0xff000000 (1768 MB)
[ 0.000000] lowmem : 0x80000000 - 0x90000000 ( 256 MB)
[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
[ 0.000000] .text : 0x80008000 - 0x80a247f0 (10354 kB)
[ 0.000000] .init : 0x80a25000 - 0x80a86080 ( 389 kB)
[ 0.000000] .data : 0x80a88000 - 0x80af9040 ( 453 kB)
[ 0.000000] .bss : 0x80af904c - 0x80b655a4 ( 434 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Switching to timer-based delay loop
[ 0.000017] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns
[ 0.002602] clocksource_of_init: no matching clocksources found
[ 0.002966] Console: colour dummy device 80x30
[ 0.003010] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[ 0.003043] pid_max: default: 32768 minimum: 301
[ 0.003454] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003481] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.005280] CPU: Testing write buffer coherency: ok
[ 0.005795] /cpus/cpu@0 missing clock-frequency property
[ 0.005832] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.005891] Setting up static identity map for 0x80745358 - 0x807453b0
[ 0.040749] Brought up 1 CPUs
[ 0.040784] SMP: Total of 1 processors activated (6.00 BogoMIPS).
[ 0.040801] CPU: All CPU(s) started in SVC mode.
[ 0.041777] devtmpfs: initialized
[ 0.051990] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.052747] pinctrl core: initialized pinctrl subsystem
[ 0.053662] regulator-dummy: no parameters
[ 0.058848] NET: Registered protocol family 16
[ 0.075332] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.076963] cpuidle: using governor ladder
[ 0.076992] cpuidle: using governor menu
[ 0.077275] Use WDOG1 as reset source
[ 0.095411] syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
[ 0.096114] vdd3p0: 2625 <--> 3400 mV at 3000 mV
[ 0.096970] cpu: 725 <--> 1450 mV at 1150 mV
[ 0.097848] vddsoc: 725 <--> 1450 mV at 1175 mV
[ 0.103025] syscon 20e4000.iomuxc-gpr: regmap [mem 0x020e4000-0x020e7fff] registered
[ 0.109605] syscon 21ac000.romcp: regmap [mem 0x021ac000-0x021affff] registered
[ 0.111186] syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
[ 0.118596] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.118626] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.122646] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.125390] 20dc000.gpc supply pu not found, using dummy regulator
[ 0.157363] bio: create slab <bio-0> at 0
[ 0.164043] mxs-dma 1804000.dma-apbh: initialized
[ 0.165004] can-3v3: 3300 mV
[ 0.165553] VSD_3V3: 3300 mV
[ 0.166315] usb_otg1_vbus: 5000 mV
[ 0.166886] vref-3v3: 3300 mV
[ 0.168181] gpio_dvfs: 1300 <--> 1400 mV at 1400 mV
[ 0.169465] i2c-core: driver [max17135] using legacy suspend method
[ 0.169490] i2c-core: driver [max17135] using legacy resume method
[ 0.170729] SCSI subsystem initialized
[ 0.172051] usbcore: registered new inte**ce driver usbfs
[ 0.172249] usbcore: registered new inte**ce driver hub
[ 0.172570] usbcore: registered new device driver usb
[ 0.177384] i2c i2c-0: IMX I2C adapter registered
[ 0.179867] i2c i2c-1: IMX I2C adapter registered
[ 0.180177] Linux video capture inte**ce: v2.00
[ 0.180373] pps_core: LinuxPPS API ver. 1 registered
[ 0.180394] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.180458] PTP clock support registered
[ 0.183166] MIPI CSI2 driver module loaded
[ 0.183748] Advanced Linux Sound Architecture Driver Initialized.
[ 0.185711] Bluetooth: Core ver 2.18
[ 0.185835] NET: Registered protocol family 31
[ 0.185857] Bluetooth: HCI device and connection manager initialized
[ 0.185895] Bluetooth: HCI socket layer initialized
[ 0.185925] Bluetooth: L2CAP socket layer initialized
[ 0.186032] Bluetooth: SCO socket layer initialized
[ 0.187011] cfg80211: Calling CRDA to update world regulatory domain
[ 0.187887] Switched to clocksource mxc_timer1
[ 0.212878] NET: Registered protocol family 2
[ 0.214845] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.214937] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.215029] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.215148] TCP: reno registered
[ 0.215182] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.215242] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.215835] NET: Registered protocol family 1
[ 0.216581] RPC: Registered named UNIX socket transport module.
[ 0.216609] RPC: Registered udp transport module.
[ 0.216627] RPC: Registered tcp transport module.
[ 0.216643] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.217164] Trying to unpack rootfs image as initramfs...
[ 1.643124] Freeing initrd memory: 7960K (83801000 - 83fc7000)
[ 1.645308] imx rpmsg driver is registered.
[ 1.646910] Bus freq driver module loaded
[ 1.649095] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 1.667498] VFS: Disk quotas dquot_6.5.2
[ 1.668318] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.674214] NFS: Registering the id_resolver key type
[ 1.674320] Key type id_resolver registered
[ 1.674341] Key type id_legacy registered
[ 1.674424] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.676285] fuse init (API version 7.22)
[ 1.677509] msgmni has been set to 484
[ 1.685600] io scheduler noop registered
[ 1.685633] io scheduler deadline registered
[ 1.686112] io scheduler cfq registered (default)
[ 1.687124] imx-weim 21b8000.weim: Driver registered.
[ 1.692849] backlight.9 supply power not found, using dummy regulator
[ 1.696069] MIPI DSI driver module loaded
[ 1.700562] 21c8000.lcdif supply lcd not found, using dummy regulator
[ 1.705927] mxsfb 21c8000.lcdif: failed to find mxc display driver
[ 1.715837] Console: switching to colour frame buffer device 100x30
[ 1.722967] mxsfb 21c8000.lcdif: initialized
[ 1.730555] imx-sdma 20ec000.sdma: no event needs to be remapped
[ 1.730766] imx-sdma 20ec000.sdma: loaded firmware 3.1
[ 1.738781] imx-sdma 20ec000.sdma: initialized
[ 1.740225] Serial: IMX driver
[ 1.740885] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58, base_baud = 5000000) is a IMX
[ 2.493690] console [ttymxc0] enabled
[ 2.499110] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 59, base_baud = 5000000) is a IMX
[ 2.509117] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60, base_baud = 5000000) is a IMX
[ 2.518790] serial: Freescale lpuart driver
[ 2.526763] imx sema4 driver is registered.
[ 2.531260] [drm] Initialized drm 1.1.0 20060810
[ 2.537049] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[ 2.564620] brd: module loaded
[ 2.579291] loop: module loaded
[ 2.585974] spi_gpio spi4.15: gpio-miso property not found, switching to no-rx mode
[ 2.604726] CAN device driver inte**ce
[ 2.612093] flexcan 2090000.can: device registered (reg_base=90970000, irq=142)
[ 2.622159] flexcan 2094000.can: device registered (reg_base=90978000, irq=143)
[ 2.631771] 20b4000.ethernet supply phy not found, using dummy regulator
[ 2.639860] pps pps0: new PPS source ptp0
[ 2.644423] fec 20b4000.ethernet (unregistered net_device): Invalid MAC address: 00:00:00:00:00:00
[ 2.653648] fec 20b4000.ethernet (unregistered net_device): Using random MAC address: 0e:bf:e7:70:dd:e1
[ 2.663844] libphy: fec_enet_mii_bus: probed
[ 2.670052] fec 20b4000.ethernet eth0: registered PHC device 0
[ 2.677538] 2188000.ethernet supply phy not found, using dummy regulator
[ 2.685567] pps pps1: new PPS source ptp1
[ 2.690116] fec 2188000.ethernet (unregistered net_device): Invalid MAC address: 00:00:00:00:00:00
[ 2.699242] fec 2188000.ethernet (unregistered net_device): Using random MAC address: 92:a6:c2:7e:13:67
[ 2.710707] fec 2188000.ethernet eth1: registered PHC device 1
[ 2.718304] PPP generic driver version 2.4.2
[ 2.723133] PPP BSD Compression module registered
[ 2.727967] PPP Deflate Compression module registered
[ 2.733236] usbcore: registered new inte**ce driver asix
[ 2.738853] usbcore: registered new inte**ce driver cdc_ether
[ 2.744836] usbcore: registered new inte**ce driver cdc_eem
[ 2.750802] usbcore: registered new inte**ce driver cdc_ncm
[ 2.756494] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.763087] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.768937] usbcore: registered new inte**ce driver usb-storage
[ 2.775301] usbcore: registered new inte**ce driver usbserial
[ 2.781351] usbcore: registered new inte**ce driver usbserial_generic
[ 2.788059] usbserial: USB Serial support registered for generic
[ 2.794198] usbcore: registered new inte**ce driver ftdi_sio
[ 2.800115] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.807551] usbcore: registered new inte**ce driver option
[ 2.813287] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.820411] usbcore: registered new inte**ce driver pl2303
[ 2.826127] usbserial: USB Serial support registered for pl2303
[ 2.832286] usbcore: registered new inte**ce driver cdc_xr_usb_serial
[ 2.838886] xr_usb_serial_common: Exar USB UART (serial port) driver
[ 2.845390] usbcore: registered new inte**ce driver usb_ehset_test
[ 2.853983] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
[ 2.869024] 2184200.usb supply vbus not found, using dummy regulator
[ 2.879211] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 2.884196] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 2.908064] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 2.915535] hub 1-0:1.0: USB hub found
[ 2.919516] hub 1-0:1.0: 1 port detected
[ 2.925747] mousedev: PS/2 mouse device common for all mice
[ 2.933456] input: 20cc000.snvs-pwrkey as /devices/soc0/soc.0/2000000.aips-bus/20cc000.snvs-pwrkey/input/input0
[ 2.944328] snvs_pwrkey 20cc000.snvs-pwrkey: i.MX snvs powerkey probed
[ 2.951839] edt_ft5x06 0-0038: touchscreen probe failed
[ 2.957141] edt_ft5x06: probe of 0-0038 failed with error -5
[ 2.964943] input: iMX6UL TouchScreen Controller as /devices/virtual/input/input2
[ 2.974506] <<-GTP-INFO->> GTP driver installing...
[ 2.980202] <<-GTP-INFO->> GTP Driver Version: V2.4<2014/11/28>
[ 2.986164] <<-GTP-INFO->> GTP Driver Built@17:24:12, Aug 7 2017
[ 2.992399] <<-GTP-INFO->> GTP I2C Address: 0x5d
[ 2.997099] 0-005d supply vdd_ana not found, using dummy regulator
[ 3.003476] 0-005d supply vcc_i2c not found, using dummy regulator
[ 3.009877] <<-GTP-INFO->> Guitar reset
[ 3.139035] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -5!
[ 3.147106] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 3.155345] <<-GTP-INFO->> Guitar reset
[ 3.278986] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -5!
[ 3.285973] <<-GTP-ERROR->> GTP i2c test failed time 1.
[ 3.309040] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 3.317240] <<-GTP-INFO->> Guitar reset
[ 3.438988] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -5!
[ 3.445975] <<-GTP-ERROR->> GTP i2c test failed time 2.
[ 3.468976] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 3.477175] <<-GTP-INFO->> Guitar reset
[ 3.598982] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -5!
[ 3.605968] <<-GTP-ERROR->> GTP i2c test failed time 3.
[ 3.628956] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 3.637154] <<-GTP-INFO->> Guitar reset
[ 3.758992] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -5!
[ 3.765978] <<-GTP-ERROR->> GTP i2c test failed time 4.
[ 3.789003] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -5! Process reset.
[ 3.797204] <<-GTP-INFO->> Guitar reset
[ 3.918977] <<-GTP-ERROR->> I2C Write: 0x8041, 1 bytes failed, errcode: -5!
[ 3.925962] <<-GTP-ERROR->> GTP i2c test failed time 5.
[ 3.947916] <<-GTP-ERROR->> I2C communication ERROR!
[ 3.952942] goodix-ts: probe of 0-005d failed with error -5
[ 3.958931] i2c-core: driver [isl29023] using legacy suspend method
[ 3.965225] i2c-core: driver [isl29023] using legacy resume method
[ 3.972686] rtc-rx8010 0-0032: Unable to write register #23
[ 3.978356] i2c i2c-0: probing for rx8010 failed
[ 3.983023] rtc-rx8010: probe of 0-0032 failed with error -5
[ 3.990102] snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc0
[ 3.998796] i2c /dev entries driver
[ 4.003536] IR NEC protocol handler initialized
[ 4.008183] IR RC5(x) protocol handler initialized
[ 4.012999] IR RC6 protocol handler initialized
[ 4.017550] IR JVC protocol handler initialized
[ 4.022135] IR Sony protocol handler initialized
[ 4.026775] IR RC5 (streamzap) protocol handler initialized
[ 4.032395] IR SANYO protocol handler initialized
[ 4.037119] IR MCE Keyboard/mouse protocol handler initialized
[ 4.045819] pxp-v4l2 pxp_v4l2.10: initialized
[ 4.050752] usbcore: registered new inte**ce driver uvcvideo
[ 4.056528] USB Video Class driver (1.1.1)
[ 4.061752] i2c-core: driver [mag3110] using legacy suspend method
[ 4.068036] i2c-core: driver [mag3110] using legacy resume method
[ 4.075250] imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)
[ 4.083875] Bluetooth: HCI UART driver ver 2.2
[ 4.088407] Bluetooth: HCI H4 protocol initialized
[ 4.093224] Bluetooth: HCI BCSP protocol initialized
[ 4.098242] Bluetooth: HCIATH3K protocol initialized
[ 4.103443] usbcore: registered new inte**ce driver bcm203x
[ 4.109475] usbcore: registered new inte**ce driver btusb
[ 4.115161] usbcore: registered new inte**ce driver ath3k
[ 4.120906] usbcore: registered new inte**ce driver rtk_btusb
[ 4.127324] sdhci: Secure Digital Host Controller Inte**ce driver
[ 4.133587] sdhci: Copyright(c) Pierre Ossman
[ 4.138002] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.146217] mmc0: no vqmmc regulator found
[ 4.187962] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[ 4.212796] nand: No NAND device found
[ 4.218827] gpmi-nand 1806000.gpmi-nand: driver registration failed: -19
[ 4.246092] usbcore: registered new inte**ce driver usbhid
[ 4.251887] usbhid: USB HID core driver
[ 4.262536] wm8960 1-001a: Failed to issue reset
[ 4.267404] wm8960: probe of 1-001a failed with error -5
[ 4.275579] fsl-asrc 2034000.asrc: driver registered
[ 4.288607] imx-wm8960 sound.14: failed to find codec platform device
[ 4.295206] imx-wm8960: probe of sound.14 failed with error -22
[ 4.304433] NET: Registered protocol family 26
[ 4.309455] TCP: cubic registered
[ 4.314423] NET: Registered protocol family 10
[ 4.321688] sit: IPv6 over IPv4 tunneling driver
[ 4.328345] NET: Registered protocol family 17
[ 4.332983] can: controller area network core (rev 20120528 abi 9)
[ 4.339510] NET: Registered protocol family 29
[ 4.344043] can: raw protocol (rev 20120528)
[ 4.348395] can: broadcast manager protocol (rev 20120528 t)
[ 4.354102] can: netlink gateway (rev 20130117) max_hops=1
[ 4.360581] Bluetooth: RFCOMM TTY layer initialized
[ 4.365537] Bluetooth: RFCOMM socket layer initialized
[ 4.370914] Bluetooth: RFCOMM ver 1.11
[ 4.374717] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 4.380173] Bluetooth: BNEP filters: protocol multicast
[ 4.385533] Bluetooth: BNEP socket layer initialized
[ 4.390652] Bluetooth: HIDP (Human Inte**ce Emulation) ver 1.2
[ 4.396624] Bluetooth: HIDP socket layer initialized
[ 4.401769] 8021q: 802.1Q VLAN Support v1.8
[ 4.406127] Key type dns_resolver registered
[ 4.412130] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 4.441825] gpio_dvfs: disabling
[ 4.445103] vref-3v3: disabling
[ 4.448479] usb_otg1_vbus: disabling
[ 4.452181] can-3v3: disabling
[ 4.455318] regulator-dummy: disabling
[ 4.460135] imx mcc test is registered.
[ 4.464894] snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 1970-01-04 00:44:26 UTC (261866)
[ 4.493465] ALSA device list:
[ 4.496477] No soundcards found.
[ 4.501244] Freeing unused kernel memory: 388K (80a25000 - 80a86000)
mount: special device /dev/mmcblk0p1 does not exist
flash_erase: error!: /dev/mtd0
error 2 (No such file or directory)
unable to create a temporary file
flash_erase: error!: /dev/mtd2
error 2 (No such file or directory)
flash_erase: error!: /dev/mtd4
error 2 (No such file or directory)
nandwrite: error!: /dev/mtd4
error 2 (No such file or directory)
flash_erase: error!: /dev/mtd1
error 2 (No such file or directory)
nandwrite: error!: /dev/mtd1
error 2 (No such file or directory)
nandwrite: error!: /dev/mtd1
error 2 (No such file or directory)
[ 4.654189] mmc0: host does not support reading read-only switch. assuming write-enable.
nandwrite: error!: /dev/mtd1
error 2 (No such file or directory)
nandwrite: error!: /dev/mtd1
error 2 (No such file or directory)
[ 4.679182] mmc0: new SD card at address e33b
flash_erase: error!: /dev/mtd3
error 2 (No such [ 4.690967] mmcblk0: mmc0:e33b SD01G 982 MiB
file or directory)
nandwrite: error!: /dev/mtd3
error 2 (No such file or directory)
[ 4.709733] mmcblk0: p1
nandwrite: error!: /dev/mtd3
error 2 (No such file or directory)
nandwrite: error!: /dev/mtd3
error 2 (No such file or directory)
nandwrite: error!: /dev/mtd3
error 2 (No such file or directory)
nandwrite: error!: /dev/mtd3
error 2 (No such file or directory)
flash_erase: error!: /dev/mtd5
error 2 (No such file or directory)
mount: special device /dev/mtdblock5 does not exist
tar: can't open '/run/mmc0/system/rootfs.tar.bz2': No such file or directory
umount: /run/nand: not mounted
umount: /run/mmc0: not mounted
Update Complete!!!!!!! SD烧写系统到NAND FLASH不成功,有谁使用SD烧写系统过没吗? |
|